Icom IC-2300H Instruction Manual - Page 25

5 MEMORY OPERATION ■ General description The transceiver has 207 memory channels including 6 scan edge memory channels (3 pairs), and 1 Call channel. These channels can be individually programmed with: • Operating frequency (p. 5) • Duplex direction (p. 12) and offset (p. 15) • Subaudible tone or tone squelch and tone frequency (pp. 13, 39-41) • Skip setting* (p. 32) In addition, a total of 10 memory banks; A to J, are selectable for use by groups, and so on. *except for scan edge memory channels. ■■Programming a memory channel The VFO settings, including the Set mode contents such as subaudible tone frequency, and so on, can be programmed into a memory channel. q Set the desired frequency in the VFO mode. w Push [S.MW]. • The " " icon and the memory channel number blink. e Rotate [DIAL] to select the memory channel to be programmed. • If the selected channel is blank, only the memory channel number is displayed. r Hold down [MW] (S.MW) for 1 second to program. • 3 beeps sound. • T he memory channel number increases, when continuing to hold down [MW] (S.MW) after programming. ✔CONVENIENT Memory programming can be performed in several ways. Example; Programming the memory channel to the same (or different) memory channel, memory channel to the Call channel, and so on. Using the HM-133V z Set the desired frequency in the VFO mode. x Push [FUNC] , and then push [MW] . • The " " icon and the memory channel number blink. c Push [Y] or [Z] to select the memory channel to be programmed. (direct numeric input cannot be used.) v Push [FUNC] , and then hold down [MW] for 1 second to program. ➥ 3 beeps sound and the VFO contents (including the subaudible tone frequency, and so on.) are programmed. ➥ The memory channel number increases, when continuing to hold down [MW] after programming. 17 [i.e.]: Programming 145.870 MHz into memory channel 20 via the front panel. Push [V/MHz]. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Rotate [DIAL] to set the frequency. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Push [S.MW]. MUTE NAR MID LOW LOCK SET ANM MONI DUP LOW DIGITAL PRIO AO BUSY T-SCAN TONE PRIO M/CALL SCAN V/ MHz Rotate [DIAL] to select the memory channel to be programmed. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Hold down [S.MW] for 1 second. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Beep Beep Beep MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz [i.e.]: Programming 145.870 MHz into the memory channel 20, using the microphone. Push . MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Push . MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Push , and then . MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Push MUTE NAR MID LOW LOCK SET ANM MONI / . DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Push MUTE , and then hold down DIGITAL PRIO AO BUSY LOCK SET MUTE NAR MID LOW LOCK SET ANM MONI ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Beep Beep Beep DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz for 1 second.