Icom IC-2300H Instruction Manual - Page 29

5 MEMORY OPERATION ■ Programming channel names Each memory channel and the Call channel can be programmed with an alphanumeric channel name, for easy recognition. Names can be a maximum of 6 characters- see the table to the right, for the selectable characters. q Push [M/CALL] to select the memory mode. w Rotate [DIAL] to select the desired memory channel. e Hold down [ANM] (MONI) for 1 second to switch the channel name display. • Two beeps sound. • T he name is displayed, if programmed. r Push [SET] to enter the channel name programming mode. t Rotate [DIAL] to select a character. • The selected character blinks. y Push [SET] or [MONI] to move the cursor to the left or right. u Repeat steps t and y, until the desired channel name is completed. i Push any key other than [SET] or [MONI], to program the name and exit the channel name programming mode. • T o switch to the frequency display, hold down [MONI] (ANM) for 1 second again. IMPORTANT!: While the channel name display mode is selected, and when [SET] is pushed, the channel name programming mode is always accessed. To access the Set mode, cancel the channel name display by holding down [MONI] (ANM) for 1 second. (A) (B) (C) (D) (E) (F) (G) (H) (I) (J) (K) (L) (M) (N) (O) (P) (Q) (R) (S) (T) (U) (V) (W) (X) (Y) (Z) (1) (2) (3) (4) (5) (6) (7) (8) (9) (0) (!) (") (#) ($) (]) (^) (space) [i.e.]: Programming "CLUB" into memory channel 5. Select memory channel 5, and then hold down [ANM] (MONI) for 1 second. DIGITAL PRIO AOBUSY MUTE NAR Channel name display MID LOW (The name is displayed, if programmed.) LOCK ANM DUP T-SCAN PRIO SCAN SET MONI LOW TONE M/CALL V/MHz Push [SET]. MUTE NAR MID LOW LOCK SET ANM MONI DUP LOW DIGITAL PRIO AO BUSY T-SCAN TONE PRIO M/CALL SCAN V/ MHz Rotate [DIAL] to select the character, and then push [SET] or [MONI] to move the cursor. SET ANM MONI DUP LOW PRIO AO BUSY PRIO M/CALL SCAN V/ MHz MUTE NAR MID LOW LOCK SET ANM MONI DUP LOW Repeat until the name is complete. PRIO AO BUSY PRIO M/CALL SCAN V/ MHz Push any other keys than [SET] or [MONI]. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Using the HM-133V z Select the memory or Call channel to be assigned the memory name. x Push [FUNC] , and then push [ANM] . • T he name is displayed, if programmed. c Push [set] . v Push [Y] or [Z] to select the desired character. • The selected character blinks. b Push [set] or [ent] to move the cursor to the left or right. n Repeat steps v and b until the desired channel names are completed. m Push [CLR] to program the name and exit the channel name programming mode. , If desired, push [FUNC] , and then push [ANM] to return to the frequency display. 21 [i.e.]: Programming "CLUB" into memory channel 5. Select memory channel 5, push then . DIGITAL PRIO AOBUSY MUTE NAR Channel name display MID LOW (The name is displayed, if programmed.) LOCK ANM DUP T-SCAN PRIO SCAN SET MONI LOW TONE M/CALL V/MHz Push . MUTE NAR MID LOW LOCK SET ANM MONI DUP LOW DIGITAL PRIO AO BUSY T-SCAN TONE PRIO M/CALL SCAN V/ MHz Push / and then push SET ANM MONI DUP LOW Push . MUTE NAR MID LOW LOCK SET ANM MONI DUP LOW to select the character, or to move the cursor. PRIO AO BUSY PRIO M/CALL SCAN V/ MHz MUTE NAR MID LOW LOCK SET ANM MONI DUP LOW Repeat until the name is complete. DIGITAL PRIO AO BUSY T-SCAN TONE PRIO M/CALL SCAN V/ MHz PRIO AO BUSY PRIO M/CALL SCAN V/ MHz