Icom IC-2300H Instruction Manual - Page 30

MEMORY OPERATION 5 ■ Memory clearing Contents of programmed memories can be cleared (blanked). q Push [V/MH­z­ ] to select the VFO mode. w Push [S.MW]. • T he " " icon and the memory channel number blink. e Rotate [DIAL] to select the memory channel to be cleared. • Memory channels not yet programmed are blank. r Push [S.MW], and then sequentially hold down [MW] (S.MW) again for 1 second ☞ This operation must be performed within 1.5 seconds. • 3 beeps sound, and then the memory channel is cleared. • The " " icon and memory channel number blink. • W hen clearing the Call channel, the current VFO contents are automatically re-programmed into the Call channel. t Push any key other than [S.MW], to return to the VFO mode. NOTE: Be careful!- the contents of cleared memories CANNOT be recalled. [i.e.]: Clearing memory channel 20. Push [V/MHz] to select the VFO mode. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Push [S.MW]. MUTE NAR MID LOW LOCK SET ANM MONI DUP LOW DIGITAL PRIO AO BUSY T-SCAN TONE PRIO M/CALL SCAN V/ MHz Rotate [DIAL] to select the memory channel. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Push [S.MW], and within 1.5 seconds, hold down [MW] (S.MW) for 1 second again. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Push any key other than [S.MW]. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Using the HM-133V z Push [VFO] to select the VFO mode. x PPuusshh[V[/FMUHzN]Cto]selec,t athnedVFthOemnopdue.sh [MW] . c PMUTuE sh [Y] or [Z] to select DIGITAL PRIO AO BUSY the memory channel to be NAR cLMOIDlWeared. LOCK ANM DUP T-SCAN PRIO SCAN • The " SET MONI " icon and channel LOW TONE M/CALL V/MHz number blink. •P uMshem[So.MrWy ]c.hannels not yet programmed are blank. v PMUTuE sh [FUNC] then DIGITAL PRIO AO BUSY [MW] , and then push NAR [LMOFIDW UNC] then hold down [MW] for 1 second. LOCK ANM DUP T-SCAN PRIO SCAN ☞ This SET MONI operation must LOW TONE M/CALL V/MHz be performed within 1.5 seconds. •R o3tabtee[eDpIAsLs] otousnedle,ctathnedmtehmeonrythcheanmneel.mory channel is MUcTEleared. DIGITAL PRIO AO BUSY NAR • The " MID LOW " icon and memory channel number blink. • W hen clearing the Call channel, the current VFO LOCK SET ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz conditions are automatically re-programmed into Ptuhseh [CS.aMllWc]h, aanndnweilt.hin 1.5 seconds, b hPouldsdhow[cnl[MrW] ] (S.,MtWo )refotru1rnsetcoontdheagVaiFn.O mode. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Push any key other than [S.MW]. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz [i.e.]: Clearing memory channel 20. Push to select the VFO mode. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Push then . MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Rotate MUTE NAR MID LOW LOCK SET ANM MONI / to select the memory channel. DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Push push then , and within 1.5 seconds, then hold down for 1 second again. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz Push . MUTE NAR MID LOW LOCK SET ANM MONI DUP LOW DIGITAL PRIO AO BUSY T-SCAN TONE PRIO M/CALL SCAN V/ MHz 00 Push MUTE NAR MID LOW LOCK AN SET MO Push MUTE NAR MID LOW LOCK AN SET MO Rotate 1MUTE NAR MID LOW 2LOCK SET AN MO P3ush p4ush 5MUTE NAR MID LOW 6LOCK SET AN MO P7ush 8MUTE NAR MID LOW 9LOCK SET AN MO 10 11 12 13 22