Icom IC-2300H Instruction Manual - Page 61

53

11

OTHER FUNCTIONS

■

Data cloning

Cloning allows you to quickly and easily transfer the

programmed contents from one transceiver to another,

or data from a personal computer to a transceiver, us-

ing the optional CS-2300H

CLONING

SOFTWARE

.

D

Cloning between two transceivers

q

Connect the master and sub-transceivers using the

OPC-474 cloning cable through the speaker jack.

• The master transceiver is used to send data to the

sub-transceiver.

w

Enter the cloning mode as following.

For the master transceiver:

While holding down

[M/CALL]

(PRIO), hold down

[

]

for 1 second to turn ON the power.

For the sub-transceiver:

Hold down

[

]

1 second to turn ON the power.

• “CLONE” appears and the transceivers enter the

cloning standby mode.

e

Push

[S.MW]

on the master transceiver.

• “CL OUT” appears on the master transceiver’s display

and the S/RF meter shows that data is being transferred

to the sub-transceiver.

• “CL IN” appears on the sub-transceiver’s display

and the S/RF meter shows that data is being received

from the master transceiver.

r

When the cloning is ﬁnished, turn OFF both trans-

ceiver's power, and then turn ON the power again to

exit the cloning mode.

D

Cloning using a PC

Data can be transferred to and from a PC, using the

optional CS-2300H

CLONING

SOFTWARE

and OPC-478

(RS-232C type) or OPC-478UC (USB type)

CLON

-

ING

CABLE

. Consult the CS-2300H

CLONING

SOFTWARE

HELP ﬁle for details.

Cloning error

D

NOTE: DO NOT

push any key on the sub-transceiver

while cloning. This will cause an error.

When the display to the right appears, a cloning error

has occurred.

In this case, both transceivers automatically return to

the clone standby mode. Please follow the cloning pro-

cedures again.

PC

to the USB port

to the RS-232C port

OPC-478

OPC-478UC

or

LOCK

S

E

T

ANM

MONI

DUP

LOW

T-SCAN

TONE

PRIO

M/CALL

SCAN

V/MHz

DIGITAL PRIO AO BUSY

MUTE

NAR

MID

LOW

Push

[S.MW]

to start cloning

(master transceiver).

While cloning

LOCK

S

E

T

ANM

MONI

DUP

LOW

T-SCAN

TONE

PRIO

M/CALL

SCAN

V/MHz


MUTE

NAR

MID

LOW

While holding down

[PRIO]

(M/CALL)

for 1 second, turn ON the power.

During cloning mode

LOCK

S

E

T

ANM

MONI

DUP

LOW

T-SCAN

TONE

PRIO

M/CALL

SCAN

V/MHz


MUTE

NAR

MID

LOW

1

00

2

3

4

5

6

7

8

9

10

11

12

13

Section	Page
Front cover	1
FOREWORD	2
IMPORTANT	2
EXPLICIT DEFINITIONS	2
SUPPLIED ACCESSORIES	2
OPTIONS	2
FCC INFORMATION	2
PRECAUTIONS	3
TABLE OF CONTENTS	4
QUICK REFERENCE GUIDE	5
■ Installation	5
Location	5
Using the mounting bracket	5
Battery connection	5
DC power supply connection	5
Antenna installation	6
Connecting the microphone	6
■ Your first contact	7
■ Repeater operation	7
■ Programming memory channels	8
1 PANEL DESCRIPTION	9
■ Front panel	9
■ Function display	10
■ Rear panel	11
■ Microphone (HM-133V)	11
■ Microphone keypad	12
2 SETTING A FREQUENCY	13
■ Preparation	13
■ Using the dial	13
■ Using the keypad on the HM-133V	13
■ Using [UP] or [DN] on the HM-133V	13
■ Tuning step selection	14
■ Lock functions	15
Lock function	15
Microphone Keypad Lock	15
3 BASIC OPERATION	16
■ Receiving	16
■ Monitor function	16
■ Audio mute function	17
■ Squelch attenuator	17
■ S-meter squelch	17
■ Transmitting	18
■ Selecting output power	19
■ One-touch PTT function	19
■ Accessing a repeater	20
■ Subaudible tones (Encoder function)	21
Subaudible tones	21
DTMF tones	22
1750 Hz tone	22
4 REPEATER SETTING	23
■ Frequency Offset	23
■ Repeater Lockout	23
■ Reversed Duplex function	24
■ Auto repeater (Only USA versions)	24
Setting the Auto Repeater function ON/OFF	24
Frequency range and offset direction	24
5 MEMORY OPERATION	25
■ General description	25
■ Programming a memory channel	25
■ Memory channel selection	26
Using the tuning dial	26
Using [UP] or [DN] on the HM-133V	26
Using the keypad on the HM-133V	26
■ Copying memory contents	27
Memory/Call channel➪VFO	27
Memory/Call channel➪Call/memory channel	28
■ Programming channel names	29
■ Memory clearing	30
■ Memory bank setting	31
■ Memory bank selection	32
■ Transferring bank links	33
■ Erasing bank links	34
6 CALL CHANNEL OPERATION	35
■ Call channel selection	35
■ Copying Call channel contents	35
■ Programming a Call channel	36
7 SCAN OPERATION	37
■ Scan types	37
■ Scan start/stop	38
Preparation	38
Operation	38
■ Scan edges programming	39
■ Skip channel setting	40
■ Scan Resume function	41
8 PRIORITY WATCH	42
■ Priority Watch types	42
■ Priority watch operation	43
9 DTMF MEMORY ENCODER	44
■ Programming a DTMF code	44
■ Transmitting a DTMF code	45
Automatic transmission (DTMF memory)	45
Transmitting a DTMF memory using theHM-133V	45
Manual transmission using the HM-133	45
■ DTMF TX speed	46
10 POCKET BEEP AND TONE SQUELCH	47
■ Pocket beep operation	47
Waiting for a call from the specific station	47
Calling a waiting station using pocket beep	48
■ Tone/DTCS squelch operation	49
■ Tone scan	50
11 OTHER FUNCTIONS	51
■ Set mode	51
■ Initial Set mode	55
Entering the Initial Set mode	55
■Weather channel operation (Only USA versions)	58
Weather channel selection	58
Weather alert function	58
■ Microphone keys	59
[F-1] and [F-2] keys on the HM-133V	59
[UP] and [DN] keys on a microphones other than the HM-133V	59
■ Partial reset	60
■ All Reset	60
■ Data cloning	61
Cloning between two transceivers	61
Cloning using a PC	61
Cloning error	61
12 SPECIFICATIONS	62
13 MAINTENANCE	63
■ Troubleshooting	63
■ Fuse replacement	63

Icom IC-2300H Instruction Manual - Page 61

■ Data cloning, Cloning between two transceivers, Cloning using a PC, Cloning error - programming software

Page 61 highlights