Icom IC-2300H Instruction Manual - Page 53

OTHER FUNCTIONS 11 DDRepeater tone Select the subaudible tone needed to access the repeater. A total of 50 tone frequencies (67.0-254.1 Hz) are selectable. (default: 88.5 Hz) MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz DDTuning step 00 Set the VFO tuning step to 5, 6.25, 10, 12.5, 15, 20, 25, 30 or 50 kHz. (default: Depending on the versions) MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz DDScan pause timer DDTone squelch frequency Select the scan pause timer option. Select the CTCSS tone frequency to use for the Tone When receiving a signal, the scan pauses according to Squelch function. the scan Pause Timer. (default: SCP-10) A total of 50 tone frequencies (67.0-254.1 Hz) are se- • "SCP-2"-"SCP-20" : W hen receiving a signal, the lectable. (default: 88.5 Hz) scan pauses for 2 to 20 seconds 1 (set in 2 seconds steps). MUTE DIGITAL PRIO AO BUSY • "SCP-HO" : W hen a signal is received, the 2 NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN scan pauses until it disappears. 3 SET MONI LOW TONE M/CALL V/MHz DIGITAL PRIO AO BUSY DIGITAL PRIO AO BUSY MUTE NAR MUTE NAR 4 MID MID • Selectable subaudible tone frequencies LOW LOCK SET ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz LOW LOCK SET ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz 5 67.0 79.7 94.8 110.9 131.8 156.7 171.3 186.2 203.5 229.1 69.3 82.5 97.4 114.8 136.5 159.8 173.8 189.9 206.5 233.6 6 71.9 85.4 100.0 118.8 141.3 162.2 177.3 192.8 210.7 241.8 74.4 88.5 103.5 123.0 146.2 165.5 179.9 196.6 218.1 250.3 77.0 91.5 107.2 127.3 151.4 167.9 183.5 199.5 225.7 254.1 DDScan resume timer Set the scan resume options of a pause after the re- 7 ceived signal disappears. (default: SCT-2) 8 DDDTCS code Set the DTCS code (both encoder and decoder) for DTCS squelch operation. A total of 104 codes are se- • "SCT-0 T he scan resumes immediately 9 after the signal disappears. • "SCT-1"-"SCT-5" : T he scan resumes 1 to 5 sec- 10 lectable. (default: 023) MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz • "SCT-HO" onds after the signal disappears. 11 : T he scan remains paused ac- cording to the Pause Timer, even 12 if the signal disappears. Rotate 13 [DIAL] to resume the scan. DDDTCS polarity Set the Transmit and Receive DTCS polarity to "NN," "NR," "RN" or "RR." (default: NN) MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz DDFrequency offset Set the duplex frequency offset between 0 and 20 MHz. In the duplex mode, the transmit frequency shifts up or down from the receive frequency by the offset amount. (default: Depending on the transceiver versions) MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz DDReverse function Turn the Reverse Duplex function ON or OFF (default). When the Reverse Duplex function is ON, the receive and transmit frequencies are reversed. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz OFF: Normal duplex (default) MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz ON: Reversed duplex MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUS DUP LOW T-SCAN TONE PRIO M/CALL DDDisplay dimmer Set the backlight brightness to between 1 (Dark) and 4 (Bright; default). MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz DDAuto dimmer Set the Auto Dimmer brightness. The Auto Dimmer function automatically reduces the backlight brightness if no operation has been performed for 5 seconds. • "ATD OF" (default): Auto Dimmer function is turned OFF. The backlight is continuously ON, while the transceiver is turned ON. • "AT OF" : The backlight automatically turns OFF if no operation has been per- formed for 5 seconds. • "AT D1" - "AT D3" : The backlight lights with the level 1 (Dark) to 3 (Bright), if no operation has been performed for 5 seconds. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz 45