Intel SR1630HGP Service Guide - Page 74

Removing the Drive Carrier SR1630HGP

Get Intel SR1630HGP - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858211901
View all Intel SR1630HGP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

3. Open the latch at the front of the hard drive carrier. See letter "A" in Figure 38. A AF001583 Figure 38. Removing the Drive Carrier (SR1630HGP) 4. Pull out on the black lever and slide the carrier from the server system. 5. Remove the four screws that attach the plastic retention device or the previously installed hard drive to the drive carrier. Two screws are at each side of the retention device or the hard drive. Store the plastic retention device for future use. See letter "A" in Figure 39. 6. Remove the hard drive from its wrapper and place it on an antistatic surface. 7. Set any jumpers and/or switches on the drive according to the drive manufacturer's instructions. 8. With the drive circuit-side down, position the connector end of the drive so it is facing the rear of the drive carrier. 9. Align the holes in the drive to the holes in the drive carrier and attach it to the carrier with the screws that were attached to the plastic retention device. See letter "B" in Figure 39. A B AF001584 Figure 39. Installing Drive into Drive Carrier (SR1630HGP) 52 Intel® Server System SR1630GP / SR1630HGP Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
52
Intel
®
Server System SR1630GP / SR1630HGP Service Guide
3.
Open the latch at the front of the hard drive carrier. See letter "A" in Figure 38.
Figure 38. Removing the Drive Carrier (SR1630HGP)
4.
Pull out on the black lever and slide the carrier from the server system.
5.
Remove the four screws that attach the plastic retention device or the previously
installed hard drive to the drive carrier. Two screws are at each side of the retention
device or the hard drive. Store the plastic retention device for future use. See letter
“A” in Figure 39.
6.
Remove the hard drive from its wrapper and place it on an antistatic surface.
7.
Set any jumpers and/or switches on the drive according to the drive manufacturer's
instructions.
8.
With the drive circuit-side down, position the connector end of the drive so it is
facing the rear of the drive carrier.
9.
Align the holes in the drive to the holes in the drive carrier and attach it to the
carrier with the screws that were attached to the plastic retention device. See letter
“B” in Figure 39.
Figure 39. Installing Drive into Drive Carrier (SR1630HGP)
A
AF0015
83
A
B
AF0015
8
4