Intel SR1630HGP Service Guide - Page 75

Removing a Hot-Swap SATA Drive (SR1630HGP)

Get Intel SR1630HGP - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858211901
View all Intel SR1630HGP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

10. With the black lever in the fully open position, slide the drive assembly into the server system (see letter "A" in Figure 40). The green latch at the front of the drive carrier must be to the right. Do not push on the black drive carrier lever until the lever begins to close by itself. 11. When the black drive carrier lever begins to close by itself, push on it to lock the drive assembly into place (see letter "B" in Figure 40). A B AF001585 Figure 40. Install Drive Assembly into the Server System (SR1630HGP) 12. Install the server system cover. For instructions, see "Installing the Server System Cover". 13. (Optional) Install the front bezel. For instructions, see "Installing the Front Bezel". 14. Plug all peripheral devices and the AC power cable into the server. Removing a Hot-Swap SATA Drive (SR1630HGP) 1. If it is installed, remove the front bezel. For instructions, see "Removing the Front Bezel". 2. Press in on the green latch at the front of the hard drive carrier. 3. Pull out on the black lever to slide the carrier from the server system. 4. Remove the four screws that attach the hard drive to the drive carrier. Lift the drive from the carrier. Store the drive in an anti-static bag. 5. If you are not installing a new drive, place the plastic retention device into the drive carrier, using the four screws you removed from the hard drive. 6. Insert the screws that held the drive in the carrier into the screw locations on the carrier for future use. 7. With the black lever in the fully open position, slide the drive carrier into the server system. The green latch must be to the right. Do not push on the black lever until the lever begins to close by itself. Intel® Server System SR1630GP / SR1630HGP Service Guide 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
Intel
®
Server System SR1630GP / SR1630HGP Service Guide
53
10.
With the black lever in the fully open position, slide the drive assembly into the
server system (see letter “A” in Figure 40). The green latch at the front of the drive
carrier must be to the right. Do not push on the black drive carrier lever until the
lever begins to close by itself.
11.
When the black drive carrier lever begins to close by itself, push on it to lock the
drive assembly into place (see letter “B” in Figure 40).
Figure 40. Install Drive Assembly into the Server System (SR1630HGP)
12.
Install the server system cover. For instructions, see
“Installing the Server System
Cover”
.
13.
(Optional) Install the front bezel. For instructions, see
“Installing the Front Bezel”
.
14.
Plug all peripheral devices and the AC power cable into the server.
Removing a Hot-Swap SATA Drive (SR1630HGP)
1.
If it is installed, remove the front bezel. For instructions, see
“Removing the Front
Bezel”
.
2.
Press in on the green latch at the front of the hard drive carrier.
3.
Pull out on the black lever to slide the carrier from the server system.
4.
Remove the four screws that attach the hard drive to the drive carrier. Lift the drive
from the carrier. Store the drive in an anti-static bag.
5.
If you are not installing a new drive, place the plastic retention device into the drive
carrier, using the four screws you removed from the hard drive.
6.
Insert the screws that held the drive in the carrier into the screw locations on the
carrier for future use.
7.
With the black lever in the fully open position, slide the drive carrier into the server
system. The green latch must be to the right. Do not push on the black lever until
the lever begins to close by itself.
A
B
AF0015
8
5