Kenmore 1317 Installation Instructions - Page 11

Install

the

door

handle

{some

Kenmore

Elite

models)

IMPORTANT."

Do

not

scratch

the

front

panel

during

this

procedure.

1.

Remove

the

door

handle

and

hardware

bag

containing

the

setscrews

and

Allen

wrench

from

the

cardboard

box.

2.

Start

set

screws

in

handle.

3.

Place

handle

on

mounting

studs.The

handle

should

appear

as a "smile"

when

installed,

with

the

set

screws

facing

down.

Push

the

door

handle

tightly

against

the

door.

Insert

the

short

end

of the

Allen

wrench

into

the

setscrews.

Tighten

the

setscrews

1/4

turn

past

snug.

Retain

Allen

wrench

with

Installation

Instructions.

stud

handle

setscrew

(in bottom of _

handle)

..._.)

wrench

Install

the

door

handle

(Kenmore

PROTM

models)

IMPORTANT.'

Do not scratch

the front

panel

during

this

procedure.

1. Remove

the

door

handle

assembly

from

the

upper

dishrack

of the

dishwasher.

2.

Remove

and

discard

the

handle

packaging.

Be sure

to

retain

the

handle

installation

instructions

and

mounting

hardware.

3. Install

the

door

handle

i

_)

per handle

installation

instructions

provided

with

the

handle

assembly.

Choose

attachment

option

Excessive

Weight

Hazard-

Use

two

or

more

people

to

move

and

install

dishwasher.

Failure

to

do

so

can

result

in

back

or

other

injury.

Using

two

or more

people,

stand

the

dishwasher

up.

Option

1,

Countertop

attachment

The

dishwasher

must

be

secured

to

the

cabinet.There

are

two

brackets

that

can

be

attached

to

the

countertop

if it

brackets

is wood,

laminate

or

another

similar

surface.

If your

countertop

is

marble,

granite

or other

hard

surface,

the

brackets

may

be

moved

to

the

sides

of

the

dishwasher.

NOTE:

Do

not

attach

the

dishwasher,

this

will

be

done

front vent

later,

model shown

Option

2,

Dishwasher

side

attachment

(for

marble,

granite

or

other

hard

surface

countertop)

1.

To remove

the

brackets

from

the

top,

flatten

tab

at back

of

brackets

with

pliers,

and

pull

the

brackets

out

of

the

slots.

/

tabs

2.

Break

offthe

end

of the

bracket

along

the

scored

line.

score

\

3.

With

another

person

holding

the dishwasher

to prevent

it from

tipping,

open

dishwasher

door,

and place

towel

over

pump

assembly

and spray

arm

of dishwasher.This

will

prevent

screws

from

falling

into

pump

area when

securing

dishwasher

to cabinet.

4.

Push the

plastic

buttons

out

of the

side of the tub.

NOTE: Save the

buttons

to cover the

holes

after

dishwasher

is installed.

Push

bracket

into

slot

on

the

side

of

dishwasher,

and

bend

tab

in

towards

the

side

of the

dishwasher

so that

it keeps

the

bracket

in place.

NOTE:

Do

not

attach

the

dishwasher,

this

will

be

done

later.

bend

i

tabs

11

Kenmore 1317 Installation Instructions - Page 11

Install, handle, option - elite

Page 11 highlights