Kenwood MDX-F1 User Manual - Page 25

To wind tape at high speed, To stop playback, Selection of reverse mode (Main unit only), Selection

Page 25 highlights

To wind tape at high speed To fast wind in direction | 4 0 To fast wind in direction \ ¢ Contents Playback of tape 25 MDX-F1 (EN) If you are operating the remote control unit, press the 1 or ¡ key. 1 TUNING 1 Operation mo mo V To stop playback STOP 0 7 Selection of reverse mode (Main unit only) 1 Select "TAPE RVS?" from the menu. MENU De SET OL 2 Select. OLUME/ MULTI CONTR Press the "SET/Demo" key while the "?" mark is blinking. " " : (REVERSE) " ": (ONE-WAY) 3 Set it. L " ": (ENDLESS) VOLUME/ MULTI CONTRO De SET Selection of TAPE EQ. (Remote control unit only) TAPE EQ. ÷ Press the 7 key to stop fast winding. ÷ Do not take out the cassette tape until the tape transport has stopped completely. Tape counter display (Remote control unit only) Each press of the TIME DISPLAY key changes the displayed contents. 1 AM 0 0 0 0 (Tape count) 2 AM 8 4 5 (Time display) The tape counter is set to "0000" when a cassette tape is loaded. By writing down the counter reading in case you want to interrupt recording (playback) in the middle of the tape, the memo will be helpful as a reference for locating the same position when continuing the recording (playback) the next time. The tape counter figure decrements during recording or playback of the back side (while the 2 tape transport indicator is lit). To set the tape counter to "0000", open the cassette holder once. Then the counter will be reset. " " : (ONE-WAY) Only one side is played back (recorded), and then the tape stops. " " : (REVERSE) Both sides are played back (recorded), and then the tape stops. (Initial setup) " " : (ENDLESS) Both sides are played back endlessly. (The tape stops after recording onto both sides.) The tape stops after recording onto both sides. The TAPE EQ. system minimizes the hiss noise heard when playing tape. When playing a tape prerecorded with Dolby NR ON, be sure to set the TAPE EQ. ON for playback. Lit when "TAPE EQ." is ON TAPE EQ. Each press switches the modes as follows. 1 "TAPE EQ." Light ......... TAPE EQ. is used. 2 "TAPE EQ." Goes off ... TAPE EQ. is not used. ÷ Select the TAPE EQ. mode according to the recording condition of the tape.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56

25
Operation
MDX-F1 (EN)
Contents
A
M
845
A
M
000
0
To wind tape at
high speed
÷
Press the
7
key to stop fast winding.
To fast wind in
direction
|
To fast wind in
direction
\
Selection of TAPE EQ.
(Remote control unit only)
The TAPE EQ. system minimizes the hiss noise heard
when playing tape. When playing a tape prerecorded
with Dolby NR ON, be sure to set the TAPE EQ. ON
for playback.
Each press switches the modes as follows.
1
“TAPE EQ.” Light
.........
TAPE EQ. is used.
2
“TAPE EQ.” Goes off ... TAPE EQ. is not used.
Lit when “TAPE EQ.” is ON
÷
Select the TAPE EQ. mode according to the recording
condition of the tape.
Tape counter display
(Remote control unit only)
Each press of the TIME DISPLAY key changes
the displayed contents.
The tape counter is set to “0000” when a cassette tape is
loaded.
By writing down the counter reading in case you want to
interrupt recording (playback) in the middle of the tape,
the memo will be helpful as a reference for locating the
same position when continuing the recording (playback)
the next time. The tape counter figure decrements dur-
ing recording or playback of the back side (while the
2
tape transport indicator is lit).
To set the tape counter to “0000”, open the cassette
holder once.
Then the counter will be reset.
1
2
(Time display)
(Tape count)
0
¢
4
1
1
TUNING
TAPE EQ.
TAPE EQ.
If you are operating the remote control unit, press
the
1
or
¡
key.
1
Select “TAPE RVS?” from the menu.
To stop playback
÷
Do not take out the cassette tape until the tape
transport has stopped completely.
Selection of reverse mode
(Main unit only)
Press the “SET/Demo”
key while the “?” mark
is blinking.
”: (ONE-WAY)
” : (REVERSE)
”:
(ENDLESS)
D
e
m
o
MENU
SET
V
O
L
U
M
E
/
M
U
L
T
I
C
O
N
T
R
O
L
V
O
L
U
M
E
/
M
U
L
T
I
C
O
N
T
R
O
L
D
e
m
o
SET
2
Select.
3
Set it.
: (ONE-WAY)
Only one side is played back (recorded), and then
the tape stops.
” : (REVERSE)
Both sides are played back (recorded), and then the
tape stops. (Initial setup)
”:
(ENDLESS)
Both sides are played back endlessly. (The tape
stops after recording onto both sides.)
The tape stops after recording onto both sides.
7
STOP
0
Playback of tape