Kenwood TM-V71A Operation Manual - Page 101

Installing The Vgs-1 Unit

Get Kenwood TM-V71A PDF manuals and user guides View all Kenwood TM-V71A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

INSTALLING THE VGS-1 UNIT Follow the instructions below to install the VGS-1 unit. 1 Remove the 8 screws from the cover of the base unit, then remove the cover itself from the unit. 2 From the 5 black cushions supplied with the VGS-1, select the thickest rectangular cushion (20 x 30 x 12 mm) and attach it to the top surface of the VGS-1 unit. • To prevent interferece to the terminal of the VGS-1, ensure that you attach the thick square cushion to the baseplate surface. cushion VGS-1 3 From the remaining cushions, select the thickest square cushion (21 x 21 x 2.5 mm) and attach it to the printed circuit board. • The remaining cushions are not used with this transceiver. • Ensure that the cushion is placed within the guidelines on the PCB. cushion 4 Insert the VGS-1 unit into the connector on the transceiver. • Press down on the top of the VGS-1 unit to ensure that it is securely attached to the connector. guidelines connector 5 Replace the cover on the base unit and secure it using the 8 screws. 93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
93
INSTALLING THE VGS-1 UNIT
Follow the instructions below to install the VGS-1 unit.
cushion
connector
1
Remove the 8 screws from the cover of
the base unit, then remove the cover itself
from the unit.
2
From the 5 black cushions supplied with
the VGS-1, select the thickest rectangular
cushion (20 x 30 x 12 mm) and attach it to
the top surface of the VGS-1 unit.
•
To prevent interferece to the terminal of the
VGS-1, ensure that you attach the thick
square cushion to the baseplate surface.
3
From the remaining cushions, select the
thickest square cushion (21 x 21 x 2.5
mm) and attach it to the printed circuit
board.
•
The remaining cushions are not used
with this transceiver.
•
Ensure that the cushion is placed within the
guidelines on the PCB.
4
Insert the VGS-1 unit into the connector
on the transceiver.
•
Press down on the top of the VGS-1 unit
to ensure that it is securely attached to the
connector.
5
Replace the cover on the base unit and
secure it using the 8 screws.
VGS-1
cushion
guidelines