Kenwood TM-V71A Operation Manual - Page 99

Installing the Panel Bracket

Get Kenwood TM-V71A PDF manuals and user guides View all Kenwood TM-V71A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

3 Connect the supplied sub-panel to the operation panel. • Install the sub-panel in a manner so as not to disrupt the cable. sub-panel 4 Connect the 8-pin connector of the supplied modular cable to the base unit. • The line filter is pre-installed onto the cable. ■ Installing the Panel Bracket 1 Clean and dry the installation location. Approx. 3 cm line filter Do not install the bracket close to an air bag. 2 Remove the release paper from the base of the panel bracket, then secure it in place using the 3 supplied self-tapping screws. self-tapping screw flat washer • Allow the panel to set for a while, to ensure it remains fast. Otherwise, vibrations may occur. • After removing the release paper, it cannot be reused. Release paper panel bracket 3 Attach the panel holder to the base bracket using the 2 supplied SEMS screws. panel holder SEMS screw 4 Attach the operation panel to the panel holder so that it locks in place. 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
91
3
Connect the supplied sub-panel to the
operation panel.
•
Install the sub-panel in a manner so as not to
disrupt the cable.
4
Connect the 8-pin connector of the supplied
modular cable to the base unit.
•
The line filter is pre-installed onto the cable.
■
Installing the Panel Bracket
1
Clean and dry the installation location.
Do not install the bracket close to an air bag.
2
Remove the release paper from the base
of the panel bracket, then secure it in place
using the 3 supplied self-tapping screws.
•
Allow the panel to set for a while, to ensure it
remains fast.
Otherwise, vibrations may occur.
•
After removing the release paper, it cannot be
reused.
3
Attach the panel holder to the base bracket
using the 2 supplied SEMS screws.
4
Attach the operation panel to the panel
holder so that it locks in place.
sub-panel
Approx. 3 cm
line filter
panel bracket
Release paper
self-tapping screw
flat washer
panel holder
SEMS screw