Kenwood TM-V71A Operation Manual - Page 12

Replacing Fuses

Get Kenwood TM-V71A PDF manuals and user guides View all Kenwood TM-V71A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

3 Connect the DC power cable to the transceiver. • Press the connectors firmly together until the locking tab clicks. Note: For your transceiver to fully exhibit its performance capabilities, we recommend using an optional PS-60 (20.5 A, 25% duty cycle) power supply. Black (-) cable Fuse holder Red (+) cable Fuse holder Regulated DC power supply DC power cable ■ Replacing Fuses If the fuse blows, determine the cause, then correct the problem. After the problem is resolved, replace the fuse. If newly installed fuses continue to blow, disconnect the power cable and contact your authorized KENWOOD dealer or an authorized KENWOOD service center for assistance. Fuse Location Transceiver (located on the DC connector) Supplied DC power cable Fuse Current Rating 15 A 20A Only use fuses of the specified type and rating; otherwise the transceiver could be damaged. Fuse Fuse holder 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
4
3
Connect the DC power cable to the transceiver.
•
Press the connectors firmly together until the locking tab clicks.
Note:
For your transceiver to fully exhibit its performance capabilities, we recommend using
an optional PS-60 (20.5 A, 25% duty cycle) power supply.
■
Replacing Fuses
If the fuse blows, determine the cause, then correct the problem.
After the
problem is resolved, replace the fuse.
If newly installed fuses continue to
blow, disconnect the power cable and contact your authorized
KENWOOD
dealer or an authorized
KENWOOD
service center for assistance.
Fuse Location
Fuse Current Rating
Transceiver
(located on the DC connector)
15 A
Supplied DC power cable
20A
Only use fuses of the specified type and rating; otherwise the transceiver could be damaged.
Black (—) cable
Red (+) cable
DC power cable
Fuse holder
Fuse holder
Regulated DC
power supply
Fuse
Fuse holder