Kenwood TM-V71A Operation Manual - Page 55

Using Program Scan

Get Kenwood TM-V71A PDF manuals and user guides View all Kenwood TM-V71A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

8 Press [F]. 9 Rotate the Tuning control to select a matching channel number from U0 to U9. • For example, if you selecte channel L3 in step 5, select channel U3 here. 10 Press [MR] to set the channel number. • The upper limit is stored in the channel. • To confirm the stored scan limits, press [MR], then select the L and U channels. Note: ◆ The lower limit must be lower in frequency than the upper limit. ◆ The lower and upper frequency step sizes must be equal. ◆ The lower and upper limits must be selected on the same band. ■ Using Program Scan 1 Select your desired band. 2 Press [VFO]. 3 Rotate the Tuning control to select a frequency within your desired scan range. 4 Press [VFO] (1s). • Scan starts at the current frequency. • The 1 MHz decimal blinks while scanning is in progress. • To reverse the scan direction, turn the Tuning control clockwise (upward scan) or counterclockwise (downward scan). You can also press microphone [UP]/ [DWN]. 5 To quit Program Scan, press [VFO] again. Note: ◆ If the step size differs between the lower limit and upper limit, VFO scan will begin instead of Program Scan. ◆ If the current VFO frequency is within more than one Program Scan range, the range stored in the smallest channel number is used. 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
47
8
Press
[F]
.
9
Rotate the
Tuning
control to select a matching channel number from U0 to
U9.
•
For example, if you selecte channel L3 in step 5, select channel U3 here.
10
Press
[MR]
to set the channel number.
•
The upper limit is stored in the channel.
•
To confirm the stored scan limits, press
[MR]
, then select the L and U
channels.
Note:
◆
The lower limit must be lower in frequency than the upper limit.
◆
The lower and upper frequency step sizes must be equal.
◆
The lower and upper limits must be selected on the same band.
■
Using Program Scan
1
Select your desired band.
2
Press
[VFO]
.
3
Rotate the
Tuning
control to select a frequency within your desired scan
range.
4
Press
[VFO] (1s)
.
•
Scan starts at the current frequency.
•
The 1 MHz decimal blinks while scanning is in progress.
•
To reverse the scan direction, turn the
Tuning
control clockwise (upward scan)
or counterclockwise (downward scan).
You can also press microphone
[UP]
/
[DWN]
.
5
To quit Program Scan, press
[VFO]
again.
Note:
◆
If the step size differs between the lower limit and upper limit, VFO scan will begin instead
of Program Scan.
◆
If the current VFO frequency is within more than one Program Scan range, the range
stored in the smallest channel number is used.