Kenwood TM-V71A Operation Manual - Page 62

Dcs Code Id

Get Kenwood TM-V71A PDF manuals and user guides View all Kenwood TM-V71A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

DCS CODE ID This function scans through all DCS codes to identify the incoming DCS code on a received signal. You may find it useful when you cannot recall the DCS code that the other persons in your group are using. 1 Press [TONE] 3 times to activate the DCS function. • The icon appears on the display when the DCS function is ON. • Each press of [TONE] changes the selection as follows: Tone (T) -> CTCSS (CT) -> DCS (DCS) -> Off (no display). 2 Press [F], [TONE] (1s). • The icon blinks and "SCAN" appears on the display. • Scan starts when a signal is received. • To reverse the scan direction, turn the Tuning control clockwise (upward scan) or counterclockwise (downward scan). You can also press microphone [UP]/ [DWN]. • To quit the scan, press [F] (ESC). • When a DCS code is identified, the identified code appears on the display and blinks. 3 Press the Tuning control to program the identified code in place of the currently set DCS code. • The DCS function will remain ON. To cancel DCS, press [TONE] until DCS no longer appears on the display. • Press [F] (ESC) if you do not want to program the identified code. • Rotate the Tuning control while an identified code is blinking, to resume scanning. 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
54
DCS CODE ID
This function scans through all DCS codes to identify the incoming DCS code on
a received signal.
You may find it useful when you cannot recall the DCS code
that the other persons in your group are using.
1
Press
[TONE]
3 times to activate the DCS function.
• The
icon appears on the display when the DCS function is ON.
• Each press of
[TONE]
changes the selection as follows:
Tone (T) –> CTCSS (CT) –> DCS (DCS) –> Off (no display).
2
Press
[F], [TONE] (1s)
.
• The
icon blinks and “SCAN” appears on the display.
•
Scan starts when a signal is received.
•
To reverse the scan direction, turn the
Tuning
control clockwise (upward scan) or
counterclockwise (downward scan).
You can also press microphone
[UP]
/
[DWN]
.
•
To quit the scan, press
[F] (ESC)
.
•
When a DCS code is identified, the identified code appears on the display and
blinks.
3
Press the
Tuning
control to program the identified code in place of the
currently set DCS code.
•
The DCS function will remain ON.
To cancel DCS, press
[TONE]
until DCS no
longer appears on the display.
• Press
[F] (ESC)
if you do not want to program the identified code.
• Rotate the
Tuning
control while an identified code is blinking, to resume scanning.