Kenwood TM-V71A Operation Manual - Page 32

Character Entry

Page 32 highlights

CHARACTER ENTRY Certain menus require you to enter characters, such as the power on message and memory names. When character entry is required, a cursor will appear on the display. 1 Press the Tuning control. • The cursor will blink. 2 Rotate the Tuning control to select your desired character. • You can enter characters as described below: - Power on message, memory name, and repeater ID (K type only): 0 ~ 9, A ~ Z, -, /, @, and space - DTMF memory code: 0 ~ 9, A ~ F, and space - EchoLink memory code: 0 ~ 9, A ~ F - Memory group link and wireless remote ID (K type only): 0 ~ 9 3 Press the Tuning control to set the selected character. • The cursor will move to the next digit. • You can move the cursor to the left or right by pressing [REV] ( ) or [LOW] ( ). • You can delete the selected character by pressing [PF1] (CLR). 4 Repeat steps 2 and 3 to enter the remaining characters. • Press [F] (ESC) at any time to exit Menu mode. • Press [TONE] (BACK) at any time to cancel the Menu setup and return to the Menu selection. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108

24
CHARACTER ENTRY
Certain menus require you to enter characters, such as the power on message
and memory names.
When character entry is required, a cursor will appear on
the display.
1
Press the
Tuning
control.
The cursor will blink.
2
Rotate the
Tuning
control to select your desired character.
You can enter characters as described below:
-
Power on message, memory name, and repeater ID (K type only):
0 ~ 9, A ~ Z,
-, /, @, and space
- DTMF memory code:
0 ~ 9, A ~ F, and space
- EchoLink memory code:
0 ~ 9, A ~ F
-
Memory group link and wireless remote ID (K type only):
0 ~ 9
3
Press the
Tuning
control to set the selected character.
The cursor will move to the next digit.
You can move the cursor to the left or right by pressing
[REV] (
)
or
[LOW] (
)
.
You can delete the selected character by pressing
[PF1] (CLR)
.
4
Repeat steps 2 and 3 to enter the remaining characters.
• Press
[F] (ESC)
at any time to exit Menu mode.
• Press
[TONE] (BACK)
at any time to cancel the Menu setup and return to the Menu
selection.