Lantronix XPress-DR XPress-DR / XPress-DR-IAP - User Guide - Page 108

Disconnect Mode, Table 32 - Disconnect Mode Options

Get Lantronix XPress-DR PDF manuals and user guides View all Lantronix XPress-DR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

UDP 8.3.6 Disconnect Mode In Disconnect Mode, DTR drop either drops the connection or is ignored. Use the following table to select Disconnect Mode Options: Table 32 - Disconnect Mode Options Disconnect Mode Option 7 6 5 4 3 2 1 0 Disconnect with DTR drop (6) 1 Ignore DTR 0 Telnet mode and terminal type setup (1) Channel (port) password (2) 1 1 Hard disconnect (3) 0 Disable hard disconnect State LED off with connection (4) 1 1 Disconnect with EOT (^D) (5) 1 1. The DSTni-XPress DR will send the "Terminal Type" upon an outgoing connection. 2. A password is required for a connection to the serial port from the network. 3. The TCP connection will close even if the remote site does not acknowledge the disconnection. 4. When there is a network connection to or from the serial port, the state LED will turn off instead of blink. 5. When Ctrl D or Hex 04 are detected, the connection is dropped. Both Telnet mode and Disconnect with EOT must be enabled for Disconnect with EOT to function properly. Ctrl D will only be detected going from the serial port to the network. 6. DTR hardwired to +12VDC. This option is disabled in the DSTni-XPress DR. Note: See Table 39 - Binary to Hexadecimal Conversion Table. 8-12 DSTni-XPress DR User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
UDP
8.3.6 Disconnect Mode
In Disconnect Mode, DTR drop either drops the connection or is ignored. Use the following
table to select Disconnect Mode Options:
Table 32 - Disconnect Mode Options
Disconnect Mode Option
7
6
5
4
3
2
1
0
Disconnect with DTR drop
(6)
1
Ignore DTR
0
Telnet mode and terminal
type setup
(1)
1
Channel (port) password
(2)
1
Hard disconnect
(3)
0
Disable hard disconnect
1
State LED off with connection
(4)
1
Disconnect with EOT (^D)
(5)
1
1. The DSTni-XPress DR will send the "Terminal Type" upon an outgoing connection.
2. A password is required for a connection to the serial port from the network.
3. The TCP connection will close even if the remote site does not acknowledge the disconnection.
4. When there is a network connection to or from the serial port, the state LED will turn off instead of blink.
5. When Ctrl D or Hex 04 are detected, the connection is dropped. Both Telnet mode and Disconnect with EOT must be enabled
for Disconnect with EOT to function properly. Ctrl D will only be detected going from the serial port to the network.
6. DTR hardwired to +12VDC. This option is disabled in the DSTni-XPress DR.
Note:
See Table 39 - Binary to Hexadecimal Conversion Table.
8-12
DSTni-XPress DR User Guide