Lenovo ThinkPad T430s (English) User Guide - Page 157

: Bad CRC of Security Settings in EFI Variable. Enter ThinkPad Setup. - cmos battery

Page 157 highlights

Solution: Checksum of the supervisor password in the EEPROM is not correct. The system board should be replaced. Have the computer serviced. • Message: 0182: Bad CRC of Security Settings in EEPROM. Enter ThinkPad Setup. Solution: Checksum of the Security settings in the EEPROM is not correct. Enter ThinkPad Setup to check Security settings, Press F10 and then press Enter to restart the system. If you still have a problem, have the computer serviced. • Message: 0183: Bad CRC of Security Settings in EFI Variable. Enter ThinkPad Setup. Solution: Checksum of the Security settings in the EFI Variable is not correct. Enter ThinkPad Setup to check Security settings, Press F10 and then press Enter to restart the system. If you still have a problem, have the computer serviced. • Message: 0187: EAIA data access error Solution: The access to EEPROM is failed. Have the computer serviced. • Message: 0188: Invalid RFID Serialization Information Area Solution: The EEPROM checksum is not correct (block # 0 and 1). The system board should be replaced, and the box serial number needs to be reinstalled. Have the computer serviced. • Message: 0189: Invalid RFID configuration information area Solution: The EEPROM checksum is not correct (block # 4 and 5). The system board should be replace, and the UUID needs to be reinstalled. Have the computer serviced. • Message: 0190: Critical low-battery error Solution: The computer turned off, because the battery is low. Connect the ac power adapter to the computer and charge the battery, or replace the battery with a fully charged one. • Message: 0191: System Security - Invalid remote change requested Solution: The system configuration change has failed. Confirm the operation and try again. To clear the error, enter the ThinkPad Setup. • Message: 0192: System Security - Embedded Security hardware tamper detected Solution: The Security Chip has been replaced with a different one. Have the computer serviced. • Message: 0199: System Security - Security password retry count exceeded Solution: This message is displayed if you enter a wrong supervisor password more than three times. Confirm the supervisor password and try again. To clear the error, enter the ThinkPad Setup. • Message: 0251: System CMOS checksum bad - Default configuration used Solution: The system CMOS might have been corrupted by an application program. The computer uses the default settings. Run ThinkPad Setup to reconfigure the settings. If you still see the same error code, have the computer serviced. • Message: 0253: EFI Variable Block Data was destroyed. Solution: The system EFI Variable Block Data might have been corrupted. Press F1 to go to the ThinkPad Setup. Press F9 and then press Enter to load the default setting. Press F10 and then press Enter to restart the system. If you still have a problem, have the computer serviced. • Message: 0271: Check date and time settings Chapter 10. Troubleshooting computer problems 139

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192

Solution
: Checksum of the supervisor password in the EEPROM is not correct. The system board
should be replaced. Have the computer serviced.
Message
: 0182: Bad CRC of Security Settings in EEPROM. Enter ThinkPad Setup.
Solution
: Checksum of the Security settings in the EEPROM is not correct. Enter ThinkPad Setup to
check Security settings, Press F10 and then press Enter to restart the system. If you still have a problem,
have the computer serviced.
Message
: 0183: Bad CRC of Security Settings in EFI Variable. Enter ThinkPad Setup.
Solution
: Checksum of the Security settings in the EFI Variable is not correct. Enter ThinkPad Setup
to check Security settings, Press F10 and then press Enter to restart the system. If you still have a
problem, have the computer serviced.
Message
: 0187: EAIA data access error
Solution
: The access to EEPROM is failed. Have the computer serviced.
Message
: 0188: Invalid RFID Serialization Information Area
Solution
: The EEPROM checksum is not correct (block # 0 and 1). The system board should be replaced,
and the box serial number needs to be reinstalled. Have the computer serviced.
Message
: 0189: Invalid RFID configuration information area
Solution
: The EEPROM checksum is not correct (block # 4 and 5). The system board should be replace,
and the UUID needs to be reinstalled. Have the computer serviced.
Message
: 0190: Critical low-battery error
Solution
: The computer turned off, because the battery is low. Connect the ac power adapter to the
computer and charge the battery, or replace the battery with a fully charged one.
Message
: 0191: System Security - Invalid remote change requested
Solution
: The system configuration change has failed. Confirm the operation and try again. To clear
the error, enter the ThinkPad Setup.
Message
: 0192: System Security - Embedded Security hardware tamper detected
Solution
: The Security Chip has been replaced with a different one. Have the computer serviced.
Message
: 0199: System Security - Security password retry count exceeded
Solution
: This message is displayed if you enter a wrong supervisor password more than three times.
Confirm the supervisor password and try again. To clear the error, enter the ThinkPad Setup.
Message
: 0251: System CMOS checksum bad - Default configuration used
Solution
: The system CMOS might have been corrupted by an application program. The computer uses
the default settings. Run ThinkPad Setup to reconfigure the settings. If you still see the same error code,
have the computer serviced.
Message
: 0253: EFI Variable Block Data was destroyed.
Solution: The system EFI Variable Block Data might have been corrupted. Press F1 to go to the ThinkPad
Setup. Press F9 and then press Enter to load the default setting. Press F10 and then press Enter to restart
the system. If you still have a problem, have the computer serviced.
Message
: 0271: Check date and time settings
Chapter 10
.
Troubleshooting computer problems
139