Lenovo ThinkStation C20 Hardware Maintenance Manual - ThinkStation C20/C20x - Page 95

Disconnect the signal cable and the power cable from the rear of the optical drive

Get Lenovo ThinkStation C20 PDF manuals and user guides View all Lenovo ThinkStation C20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

4. Disconnect the signal cable and the power cable from the rear of the optical drive, press the blue release button 1 as shown, and then slide the optical drive out of the computer. Figure 24. Removing the optical drive 5. Install the optical drive retainer 1 on the side of the new optical drive. Then, slide the new optical drive into the optical drive bracket from the front of the computer until the optical drive snaps into position. Figure 25. Installing the new optical drive 6. Connect the signal cable and the power cable to the rear of the new optical drive. a. Connect the signal cable to the rear of the new optical drive. Note: If you want to replace the signal cable, remove the PCI card holder. See "Removing and reinstalling the PCI card holder" on page 76. Then, disconnect the old signal cable from the system Chapter 9. Replacing FRUs 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
4. Disconnect the signal cable and the power cable from the rear of the optical drive, press the blue release
button
1
as shown, and then slide the optical drive out of the computer.
Figure 24. Removing the optical drive
5. Install the optical drive retainer
1
on the side of the new optical drive. Then, slide the new optical drive
into the optical drive bracket from the front of the computer until the optical drive snaps into position.
Figure 25. Installing the new optical drive
6. Connect the signal cable and the power cable to the rear of the new optical drive.
a.
Connect the signal cable to the rear of the new optical drive.
Note:
If you want to replace the signal cable, remove the PCI card holder. See “Removing and
reinstalling the PCI card holder” on page 76. Then, disconnect the old signal cable from the system
Chapter 9
.
Replacing FRUs
89