Lexmark CX922 Menus Guide - Page 80

Parallel [x], PCL SmartSwitch, NPA Mode, Advanced Status, Protocol, Honor Init, Parallel Mode 2

Get Lexmark CX922 PDF manuals and user guides View all Lexmark CX922 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Network/Ports 80 Parallel [x] Note: This menu appears only when an optional parallel card is installed. Use To PCL SmartSwitch On* Off Set the printer to switch automatically to PCL emulation when a print job received through a serial port requires it, regardless of the default printer language. Note: If PCL SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu. PS SmartSwitch On* Off Set the printer to switch automatically to PS emulation when a print job received through a serial port requires it, regardless of the default printer language. Note: If PS SmartSwitch is off, then the printer does not examine incoming data and uses the default printer language specified in the Setup menu. NPA Mode On Off Auto* Set the printer to perform the special processing required for bidirectional communication, following the conventions defined by the NPA protocol. Note: The printer restarts after changing the setting. Advanced Status On* Off Enable bidirectional communication through the parallel port. Protocol Standard Fastbytes* Specify the parallel port protocol. Honor Init On Off* Set the printer to honor printer hardware initialization requests from the computer. Note: The computer requests initialization by activating the Init signal from the parallel port. Many personal computers activate the Init signal each time the computer is turned on. Parallel Mode 2 On Off* Determine whether the parallel port data is sampled on the leading or trailing edge of a strobe. Mac Binary PS On Off Auto* Set the printer to process Macintosh binary PostScript print jobs. Notes: • On processes raw binary PostScript print jobs. • Off filters print jobs using the standard protocol. ENA Address Set the network address information for an external print server. Note: This menu item is available only if the printer is attached to an external print server through the USB port. ENA Netmask Set the netmask information for an external print server. Note: This menu item is available only if the printer is attached to an external print server through the USB port. Note: An asterisk (*) next to a value indicates the factory default setting.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Parallel [x]
Note:
This menu appears only when an optional parallel card is installed.
Use
To
PCL SmartSwitch
On*
Off
Set the printer to switch automatically to PCL emulation when a print job
received through a serial port requires it, regardless of the default printer
language.
Note:
If PCL SmartSwitch is off, then the printer does not examine incoming
data and uses the default printer language specified in the Setup menu.
PS SmartSwitch
On*
Off
Set the printer to switch automatically to PS emulation when a print job received
through a serial port requires it, regardless of the default printer language.
Note:
If PS SmartSwitch is off, then the printer does not examine incoming
data and uses the default printer language specified in the Setup menu.
NPA Mode
On
Off
Auto*
Set the printer to perform the special processing required for bidirectional
communication, following the conventions defined by the NPA protocol.
Note:
The printer restarts after changing the setting.
Advanced Status
On*
Off
Enable bidirectional communication through the parallel port.
Protocol
Standard
Fastbytes*
Specify the parallel port protocol.
Honor Init
On
Off*
Set the printer to honor printer hardware initialization requests from the
computer.
Note:
The computer requests initialization by activating the Init signal from
the parallel port. Many personal computers activate the Init signal each time
the computer is turned on.
Parallel Mode 2
On
Off*
Determine whether the parallel port data is sampled on the leading or trailing
edge of a strobe.
Mac Binary PS
On
Off
Auto*
Set the printer to process Macintosh binary PostScript print jobs.
Notes:
•
On processes raw binary PostScript print jobs.
•
Off filters print jobs using the standard protocol.
ENA Address
Set the network address information for an external print server.
Note:
This menu item is available only if the printer is attached to an external
print server through the USB port.
ENA Netmask
Set the netmask information for an external print server.
Note:
This menu item is available only if the printer is attached to an external
print server through the USB port.
Note:
An asterisk (*) next to a value indicates the factory default setting.
Network/Ports
80