Linksys WPS54G User Guide - Page 29

The Protocol Tab - SNMP, General, Management Stations, Trap Receivers

Get Linksys WPS54G - Wireless-G PrintServer Print Server PDF manuals and user guides
UPC - 745883561049
View all Linksys WPS54G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Wireless-G PrintServer The Protocol Tab - SNMP Use this screen to view or change the PrintServer's SNMP (Simple Network Management Protocol) settings. The PrintServer supports SNMP, which allows network administrators to monitor and control the PrintServer through the use of network management platforms, such as HP OpenView. The appropriate MIB file must be imported into your SNMP management program using the Import-Compile command. Check your program's documentation for details on this procedure. The MIB file is named Mib2p.mib and is provided in the MiB folder on the Setup CD-ROM. General SysContact. Enter the name of the contact person in the SysContact field. SysLocation. Enter the location of the contact person in the SysLocation field. Management Stations Station No. Select the number of the management station from the Station No. drop-down menu (1-4). Click the Get Data button to display the information for the selected station. IP Address. Enter the IP address of the management station running the SNMP program. Community. Enter the name of the SNMP community, which is usually public or private. Access. Select the level of access for this management station, Not Accessible, Read-only, or Read/Write. Trap Receivers Receiver No. Select the number of the trap receiver from the Receiver No. drop-down menu (1-4). Click the Get Data button to display the information for the selected trap receiver. IP Address. Enter the IP address of the trap receiver that will be sent the trap messages or notifications. Community. In the Community field, enter the name of the SNMP community, which is usually public or private. Enable with Severity level. To designate a severity level, click the checkbox next to Enable with Severity level. From the following drop-down menu, select the desired level of severity, with 1 meaning least severe. Click the Save button to apply your changes, or click Cancel to cancel your changes. Chapter 6: Configuring the PrintServer Using the Web-based Utility The Protocol Tab - SNMP Figure 6-5: Protocol Tab - SNMP 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
23
Chapter 6: Configuring the PrintServer Using the Web-based Utility
The Protocol Tab - SNMP
Wireless-G PrintServer
The Protocol Tab - SNMP
Use this screen to view or change the PrintServer’s SNMP (Simple Network Management Protocol) settings.
The PrintServer supports SNMP, which allows network administrators to monitor and control the PrintServer
through the use of network management platforms, such as HP OpenView.
The appropriate MIB file must be imported into your SNMP management program using the Import-Compile
command. Check your program’s documentation for details on this procedure. The MIB file is named Mib2p.mib
and is provided in the MiB folder on the Setup CD-ROM.
General
SysContact
. Enter the name of the contact person in the
SysContact
field.
SysLocation
. Enter the location of the contact person in the
SysLocation
field.
Management Stations
Station No.
Select the number of the management station from the
Station No.
drop-down menu (1-4). Click the
Get Data
button to display the information for the selected station.
IP Address
. Enter the IP address of the management station running the SNMP program.
Community
. Enter the name of the SNMP community, which is usually
public
or
private
.
Access
. Select the level of access for this management station,
Not Accessible
,
Read-only
, or
Read/Write
.
Trap Receivers
Receiver No.
Select the number of the trap receiver from the
Receiver No.
drop-down menu (1-4). Click the
Get
Data
button to display the information for the selected trap receiver.
IP Address
. Enter the IP address of the trap receiver that will be sent the trap messages or notifications.
Community
. In the
Community
field, enter the name of the SNMP community, which is usually
public
or
private
.
Enable with Severity level
. To designate a severity level, click the checkbox next to
Enable with Severity level
.
From the following drop-down menu, select the desired level of severity, with 1 meaning least severe.
Click the
Save
button to apply your changes, or click
Cancel
to cancel your changes.
Figure 6-5: Protocol Tab - SNMP