Netgear WAC720 Reference Manual - Page 82

Configuration > Wireless > Advanced > QoS Policies, Destination IP

Get Netgear WAC720 PDF manuals and user guides View all Netgear WAC720 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

ProSAFE Dual-Band Wireless AC Access Point WAC720 WAC730 • Source MAC. Indicates the source MAC address in Ethernet-II frame header. • Destination MAC. Indicates the destination MAC address in Ethernet-II frame header. • Source IP. Indicates the source IP address in the IP header. • Destination IP. Indicates the destination IP address in the IP header. • Source port. Indicates the source port number in the port header. • Destination port. Indicates the destination port number in the port header. For each classification in a QoS policy, you can configure rate limiting by specifying the maximum bit rate and maximum burst rate. Packets that exceed the maximum bit rate are retained in the traffic queue and are processed when transmission falls again below the maximum bit rate. You can also configure the overall maximum bit rate and maximum burst rate for the entire wireless interface. You can configure up to eight QoS policies.  To configure a new QoS policy: 1. Select Configuration > Wireless > Advanced > QoS Policies. 2. From the Create Policy menu, select NEW. If you have not created any QoS policies, NEW is the only selection possible. 3. In the Policy Name field, enter a name for the new QoS policy. 4. Specify a classification for the QoS policy as explained in the following table. Advanced Configuration 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
Advanced Configuration
82
ProSAFE Dual-Band Wireless AC Access Point WAC720 WAC730
•
Source MAC
. Indicates the source MAC address in Ethernet-II frame header.
•
Destination MAC
. Indicates the destination MAC address in Ethernet-II frame header.
•
Source IP
. Indicates the source IP address in the IP header.
•
Destination IP
. Indicates the destination IP address in the IP header.
•
Source port
. Indicates the source port number in the port header.
•
Destination port
. Indicates the destination port number in the port header.
For each classification in a QoS policy, you can configure rate limiting by specifying the
maximum bit rate and maximum burst rate. Packets that exceed the maximum bit rate are
retained in the traffic queue and are processed when transmission falls again below the
maximum bit rate. You can also configure the overall maximum bit rate and maximum burst
rate for the entire wireless interface.
You can configure up to eight QoS policies.
To configure a new QoS policy:
1.
Select
Configuration > Wireless > Advanced > QoS Policies
.
2.
From the Create Policy menu, select
NEW
. If you have not created any QoS policies,
NEW
is the only selection possible.
3.
In the
Policy Name
field, enter a name for the new QoS policy.
4.
Specify a classification for the QoS policy as explained in the following table.