Onkyo TX-DS676 Owner Manual - Page 14

Making antenna connections

Get Onkyo TX-DS676 PDF manuals and user guides View all Onkyo TX-DS676 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Making antenna connections Outdoor antenna Indoor antenna 300 ohms ribbon wire Connecting the antenna cable to the 75/300 ohm antenna adapter (Other than North America and European models) Connecting the 300 ohm ribbon wire: Loosen the screws and wrap the wire around these screws. Then tighten the screws with a screwdriver. Connecting the coaxial cable: 1. With your fingernail or a small screwdriver, press the stoppers outward and remove the cover. 1 2 3 2. Remove the transformer wire A from slit B and insert it into slit C. Slit B ✦ ✦ ✦✦ ✦ ✦ 636 mm mm mm 15mm 3. Prepare the coaxial cable as shown in the diagram. Connect the 75/300 ohm antenna adapter to the coaxial cable. 1 Insert the end of the cable. 2 Clamp it in place with pliers. Wire A 4. Re-install the cover. Slit C Directional linkage type splitter To receiver To TV (or VCR) Directional Iinkage Do not use the same antenna for both FM and TV (or VCR) reception since the FM and TV (or VCR) signals can interfere with each other. If you must use a common FM/TV (or VCR) antenna, use a directional linkage type splitter. Insert into the hole. Assembling the AM loop antenna Assemble the loop antenna as shown in the illustration. • Refer to the next page for details on connecting the AM loop antenna. 1 2 Connecting the antenna cable 3 1. Press down the lever. 2. Insert the wire into the hole. 3. Release the lever to replace it. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
14
Making antenna connections
Connecting the antenna cable to the 75/300 ohm
antenna adapter (Other than North America and
European models)
Connecting the 300 ohm ribbon wire:
Loosen the screws and wrap the wire around these screws. Then
tighten the screws with a screwdriver.
Connecting the coaxial cable:
1.
With your fingernail or a small screwdriver, press the stoppers
outward and remove the cover.
2.
Remove the transformer wire A from slit B and insert it into slit
C.
3.
Prepare the coaxial cable as shown in the diagram.
Connect the 75/300 ohm antenna adapter to the coaxial cable.
1
Insert the end of the cable.
2
Clamp it in place with pliers.
4.
Re-install the cover.
Directional Iinkage
Do not use the same antenna for both FM and TV (or VCR) recep-
tion since the FM and TV (or VCR) signals can interfere with each
other. If you must use a common FM/TV (or VCR) antenna, use a
directional linkage type splitter.
Assembling the AM loop antenna
Assemble the loop antenna as shown in the illustration.
•
Refer to the next page for details on connecting the AM loop
antenna.
Connecting the antenna cable
1.
Press down the lever.
2.
Insert the wire into the hole.
3.
Release the lever to replace it.
1
2
3
6
mm
3
mm
6
mm
15mm
1
2
3
Outdoor
antenna
Indoor
antenna
300 ohms
ribbon wire
Slit B
Wire A
Slit C
Directional linkage
type splitter
To TV (or VCR)
To receiver
Insert into the hole.