Onkyo TX-DS676 Owner Manual - Page 52

Programming the remote controller codes, of other devices into the RC-392M - remote code

Get Onkyo TX-DS676 PDF manuals and user guides View all Onkyo TX-DS676 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Programming the remote controller codes of other devices into the RC-392M The RC-392M has two learning functions. One is a normal learning function that enables the RC-392M to learn other remote controllers' codes. The other is a macro learning function, which enables the RC-392M to learn a series of codes already memorized in the remote controller into one MACRO button. Programming procedure Any button is programmable except for the eight Mode buttons 4 (AUDIO, CD, DVD, MD, SAT, CABLE, VCR, and TV), two Macro buttons (DIRECT and MODE), and LIGHT button. RC-385S REMOTE CONTROLLER LEVEL MUTING TOTNEEST VOLUME DISC TAPE CH SEL VIDEO-2 DVGTDRAOPUEPINPTUUTTNSUEPENRLREEERCSPTEDITHOMORNMEOR MOSDUER CD INMPULUTTI-CH VIDEO-1 CD SLEEP DVD POWER 2 Light 3 1 5 to 15 cm (2 to 6 inches) RC-392M 1. Place the RC-392M and the remote controller for another device, with 5-15cm (2-6 inches) apart and the light-emitting parts facing each other. 2. While pressing and holding down the desired MODE button on the RC-392M (AUDIO, CD, DVD, MD, SAT, CABLE, VCR, or TV), press the ENT button, then release the buttons. When you press and hold down one of the MODE button, the SEND/LEARN indicator lights up. When you press the ENT button, the indicator turns off. When you release the buttons, the SEND/LEARN indicator lights up again. 3. Press and release the desired operation button on the RC392M. You may select any button within the rectangle shown in the figure. When you press the button, the SEND/LEARN indicator turns off. When you release the button, the indicator lights up again. 4. Press and hold down the desired button on the remote controller of the other device until the SEND/LEARN indicator on the RC-392M flashes twice. The SEND/LEARN indicator flashes twice slowly, then lights up. 5. Repeat Steps 3-4 to program other buttons in the same MODE. Repeat Steps 2-4 to program other buttons in a different MODE. 6. Press the MODE button to complete programming. 7. Operate the programmed button to make sure the learning function works. Note: The remote controller codes for the Onkyo CD player, tape deck, DVD player, and MD recorder have already been programmed into the buttons on the RC-392M. You may program other remote controller codes into these buttons. If you wish to restore the Onkyo preset codes after you program new codes, erase the new codes. (See page 53.) 52 Note: • The remote controller has 408 memory slots (51 buttons 8 modes), al- though this number varies significantly depending on the manufacturers and types of the remote controller you wish to program into the RC392M. It is recommended that you determine which button functions have priority for programming. • If you do not press any button for more than 30 seconds during the procedure, the SEND/LEARN indicator flashes three times quickly, then the RC-392M exits Learning mode. Resume Step 2. • If you make a mistake during programming, the SEND/LEARN indicator flashes three times quickly, then the RC-392M exits Learning mode. • If you try to program beyond the learning capacity of the RC-392M, the SEND/LEARN indicator flashes six times quickly, then the RC-392M exits Learning function. Try programming in a button of other MODE. • Follow the same procedure when you wish to program new codes into the already-programmed buttons. • This remote controller uses infrared rays. Most remote controller codes can be memorized using the infrared system; however, depending on the degree to which the system differs, there may be some rare occasions when memorization is not possible. • Some remote controllers use a single button to perform different functions, with the function code changing each time the button is pressed. If you are using this kind of controller, please perform the "learn" operations for each function individually to store each function to a button on the RC-392M. • For instructions regarding the operation of "learned" units, please refer to the instruction manual for each product. • Even after codes have been memorized, please keep your old remote controller in a safe place. If the memorized codes are lost when the batteries run down, it will be necessary to memorize them once again using the old remote controller. • Make sure both the RC-392M and the product's own remote controller have fresh batteries. If either of them has batteries that are wearing down, it may be impossible to store the remote controller codes into the RC-392M or the product may not respond properly to the buttons on the RC-392M for which the remote controller codes were stored into memory.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
52
Programming the remote controller codes
of other devices into the RC-392M
The RC-392M has two learning functions. One is a normal learning function that enables the RC-392M to learn other remote controllers’
codes. The other is a macro learning function, which enables the RC-392M to learn a series of codes already memorized in the remote
controller into one MACRO button.
Programming procedure
POWER
SLEEP
DIMMER
SUR
MODE
VIDEO-1
VIDEO-2
TAPE
DVD
C D
C D
DVD
TUNER
TUNER
PHONO
INPUT SELECTOR
DISC
TAPE
VOLUME
LEVEL
CH SEL
PRESET
MUTING
TEST
TONE
MULTI-CH
INPUT
REMOTE CONTROLLER
GROUP
RC-385S
4
3
2
1
Light
5 to 15 cm
(2 to 6 inches)
RC-392M
Any button is programmable except for the eight Mode buttons
(AUDIO, CD, DVD, MD, SAT, CABLE, VCR, and TV), two
Macro buttons (DIRECT and MODE), and LIGHT button.
1.
Place the RC-392M and the remote controller for another
device, with 5–15cm (2–6 inches) apart and the light-emit-
ting parts facing each other.
2.
While pressing and holding down the desired MODE button
on the RC-392M (AUDIO, CD, DVD, MD, SAT, CABLE,
VCR, or TV), press the ENT button, then release the but-
tons.
When you press and hold down one of the MODE button, the
SEND/LEARN indicator lights up. When you press the ENT
button, the indicator turns off. When you release the buttons, the
SEND/LEARN indicator lights up again.
3.
Press and release the desired operation button on the RC-
392M.
You may select any button within the rectangle shown in the
figure. When you press the button, the SEND/LEARN indicator
turns off. When you release the button, the indicator lights up
again.
4.
Press and hold down the desired button on the remote con-
troller of the other device until the SEND/LEARN indicator
on the RC-392M flashes twice.
The SEND/LEARN indicator flashes twice slowly, then lights
up.
5.
Repeat Steps 3–4 to program other buttons in the same
MODE.
Repeat Steps 2-4 to program other buttons in a different MODE.
6.
Press the MODE button to complete programming.
7.
Operate the programmed button to make sure the learning
function works.
Note:
The remote controller codes for the Onkyo CD player, tape
deck, DVD player, and MD recorder have already been pro-
grammed into the buttons on the RC-392M. You may program
other remote controller codes into these buttons. If you wish to
restore the Onkyo preset codes after you program new codes,
erase the new codes. (See page 53.)
Note:
•
The remote controller has 408 memory slots (51 buttons 8 modes), al-
though this number varies significantly depending on the manufacturers
and types of the remote controller you wish to program into the RC-
392M. It is recommended that you determine which button functions
have priority for programming.
•
If you do not press any button for more than 30 seconds during the pro-
cedure, the SEND/LEARN indicator flashes three times quickly, then
the RC-392M exits Learning mode. Resume Step 2.
•
If you make a mistake during programming, the SEND/LEARN indica-
tor flashes three times quickly, then the RC-392M exits Learning mode.
•
If you try to program beyond the learning capacity of the RC-392M, the
SEND/LEARN indicator flashes six times quickly, then the RC-392M
exits Learning function. Try programming in a button of other MODE.
•
Follow the same procedure when you wish to program new codes into
the already-programmed buttons.
•
This remote controller uses infrared rays. Most remote controller codes
can be memorized using the infrared system; however, depending on
the degree to which the system differs, there may be some rare occa-
sions when memorization is not possible.
•
Some remote controllers use a single button to perform different func-
tions, with the function code changing each time the button is pressed. If
you are using this kind of controller, please perform the “learn” opera-
tions for each function individually to store each function to a button on
the RC-392M.
•
For instructions regarding the operation of “learned” units, please refer
to the instruction manual for each product.
•
Even after codes have been memorized, please keep your old remote
controller in a safe place. If the memorized codes are lost when the bat-
teries run down, it will be necessary to memorize them once again using
the old remote controller.
•
Make sure both the RC-392M and the product’s own remote controller
have fresh batteries. If either of them has batteries that are wearing
down, it may be impossible to store the remote controller codes into the
RC-392M or the product may not respond properly to the buttons on the
RC-392M for which the remote controller codes were stored into
memory.