Onkyo TX-SR600 Owner Manual - Page 31

Connecting a subwoofer, Connecting to the SPEAKERS B terminals, TX-SR600/600E only, Connecting

Get Onkyo TX-SR600 PDF manuals and user guides View all Onkyo TX-SR600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Connecting speakers Connecting speakers After determining the layout of your speaker system, it is now necessary to connect the speakers correctly to your TX-SR700/ 700E/600/600E. Caution: • Be sure to connect the positive (+) and negative (-) cables for the speakers properly. If they are mixed up, the left and right signals will be reversed and the audio will sound unnatural. • Do not connect more than one speaker cable to one speaker terminal. Doing so may damage the TX-SR700/700E/600/600E. • When you listen to surround audio or select Multichannel, be sure to turn on SPEAKERS A. • Connect only speakers with an impedance between 6 and 16 Ω to the TX-SR700/700E/600/600E. Connecting speakers with an impedance lower than 6 Ω may damage the amplifier. • Even if you are using only one speaker or listening to monaural (mono) sound, never connect a single speaker in parallel to both the right and left-channel terminals. SPEAKER B (TX-SR600/600E only) 1. Strip away approx. 3/8 inch (10 mm) of the wire insulation. 2. Twist the wire ends tightly together. 3. Press the lever to open the terminal. 4. Insert the exposed wire end. 5. Release the lever to close the terminal. Leave some of the exposed wire showing outside the terminal. 3/8" (10mm) SPEAKERS -+ L L SPEAKERS -+ L L R R R R -+ -+ • To prevent damage to circuitry, never short-circuit the positive (+) and negative (-) speaker wires. Connecting a subwoofer Use the SUBWOOFER PRE OUT jack to connect a subwoofer with a built-in power amplifier. If your subwoofer does not have a built-in amplifier, connect an amplifier to the SUBWOOFER PRE OUT jack and the subwoofer to the amplifier. NO! Connecting the speaker cable 1. Strip away approx. 5/8 inch (15 mm) of the wire insulation. 2. Twist the wire ends tightly together. 3. Unscrew the speaker terminal cap. 5/8" (15mm) Connecting to the SPEAKERS B terminals (TX-SR600/600E only) If you require an additional set of front speakers (left and right), such as for use in another room, connect them to the FRONT SPEAKERS B inputs. 4. Insert the exposed wire end. 5. Screw down the speaker terminal cap. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
31
SPEAKER B (TX-SR600/600E only)
1.
Strip away approx. 3/8 inch (10 mm)
of the wire insulation.
2.
Twist the wire ends tightly together.
3.
Press the lever to open the terminal.
4.
Insert the exposed wire end.
5.
Release the lever to close the
terminal. Leave some of the exposed
wire showing outside the terminal.
Connecting a subwoofer
Use the SUBWOOFER PRE OUT jack to connect a subwoofer with
a built-in power amplifier. If your subwoofer does not have a built-in
amplifier, connect an amplifier to the SUBWOOFER PRE OUT jack
and the subwoofer to the amplifier.
Connecting to the SPEAKERS B terminals
(TX-SR600/600E only)
If you require an additional set of front speakers (left and right), such
as for use in another room, connect them to the FRONT SPEAKERS
B inputs.
Connecting speakers
Connecting speakers
After determining the layout of your speaker system, it is now
necessary to connect the speakers correctly to your TX-SR700/
700E/600/600E.
Caution:
•
Be sure to connect the positive (+) and negative (
–
) cables for the
speakers properly. If they are mixed up, the left and right signals
will be reversed and the audio will sound unnatural.
•
Do not connect more than one speaker cable to one speaker
terminal. Doing so may damage the TX-SR700/700E/600/600E.
•
When you listen to surround audio or select Multichannel, be
sure to turn on SPEAKERS A.
•
Connect only speakers with an impedance between 6 and 16
Ω
to the TX-SR700/700E/600/600E. Connecting speakers
with an impedance lower than 6
Ω
may damage the
amplifier.
•
Even if you are using only one speaker or listening to monaural
(mono) sound, never connect a single speaker in parallel to both
the right and left-channel terminals.
•
To prevent damage to circuitry, never short-circuit the positive
(+) and negative (
–
) speaker wires.
Connecting the speaker cable
1.
Strip away approx. 5/8 inch (15 mm)
of the wire insulation.
2.
Twist the wire ends tightly together.
3.
Unscrew the speaker terminal cap.
4.
Insert the exposed wire end.
5.
Screw down the speaker terminal
cap.
R
L
R
L
SPEAKERS
+
–
+
–
R
L
R
L
SPEAKERS
+
–
+
–
NO!
5/8"
(15mm)
3/8"
(10mm)