Panasonic KX-MB2061 Operating Instructions - Page 25

Setting the original - ink

Page 25 highlights

2.7 Setting the original 2.7.1 Using the scanner glass A 2. Preparation 2.7.2 Using the automatic document feeder A B 1 Open the document cover (A). 2 Place the document FACE DOWN on the scanner glass (B), aligning the top left of the document with the corner where the mark is positioned. 3 Close the document cover. Note: R Confirm that there are no documents in the automatic document feeder. R Place the original onto the scanner glass gently. To avoid malfunction, do not press down too firmly. R If the original is a thick book, do not close the document cover. R Confirm that any ink, paste or correction fluid has dried completely. R Effective scanning area is shown by the shaded area: Effective scanning area 4 mm (5/32") 289 mm (11 3/8") 4 mm (5/32") 208 mm (8 3/16") 4 mm (5/32") 4 mm (5/32") 1 Insert the document (up to 20 pages) FACE UP into the feeder until a single beep is heard. 2 Adjust the width of the document guides (A) to fit the actual size of the document. Note: R Confirm that there are no documents on the scanner glass. R Confirm that any ink, paste or correction fluid has dried completely. R Remove clips, staples or other fasteners. R Do not insert the following types of documents (Make a copy of the document using the scanner glass and set the copy instead.): - Chemically treated paper such as carbon or carbonless duplicating paper - Electrostatically charged paper - Badly curled, creased or torn paper - Paper with a coated surface - Paper with printing on the opposite side that can be seen through the other side, such as newsprint R The total height of the documents when laid flat, must be less than 4 mm (5/32"). If the documents exceed the capacity of the automatic document feeder, they may fall or cause a jam in the feeder. R To set a document with a width of less than 210 mm (8 1/4"), we recommend using the scanner glass to copy the original document onto A4 or letter-size paper, then setting the copied document for better results. R Do not set documents that do not satisfy the requirements of size and weight. Make a copy of the document using the scanner glass and set the copy. R Available document size, document weight and effective scanning area are as follows: For assistance, please visit http://www.panasonic.com/help 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160

2.7 Setting the original
2.7.1 Using the scanner glass
A
B
1
Open the document cover (
A
).
2
Place the document FACE DOWN on the scanner
glass (
B
), aligning the top left of the document with
the corner where the
mark is positioned.
3
Close the document cover.
Note:
R
Confirm that there are no documents in the automatic
document feeder.
R
Place the original onto the scanner glass gently. To
avoid malfunction, do not press down too firmly.
R
If the original is a thick book, do not close the
document cover.
R
Confirm that any ink, paste or correction fluid has
dried completely.
R
Effective scanning area is shown by the shaded area:
Effective scanning area
208 mm
(8
3
/
16
")
289
mm
(11
3
/
8
")
4 mm
(
5
/
32
")
4 mm
(
5
/
32
")
4 mm
(
5
/
32
")
4 mm
(
5
/
32
")
2.7.2 Using the automatic document feeder
A
1
Insert the document (up to 20 pages) FACE UP into
the feeder until a single beep is heard.
2
Adjust the width of the document guides (
A
) to fit the
actual size of the document.
Note:
R
Confirm that there are no documents on the scanner
glass.
R
Confirm that any ink, paste or correction fluid has
dried completely.
R
Remove clips, staples or other fasteners.
R
Do not insert the following types of documents (Make
a copy of the document using the scanner glass and
set the copy instead.):
Chemically treated paper such as carbon or
carbonless duplicating paper
Electrostatically charged paper
Badly curled, creased or torn paper
Paper with a coated surface
Paper with printing on the opposite side that can
be seen through the other side, such as newsprint
R
The total height of the documents when laid flat, must
be less than 4 mm (
5
/
32
"). If the documents exceed
the capacity of the automatic document feeder, they
may fall or cause a jam in the feeder.
R
To set a document with a width of less than 210 mm
(8
1
/
4
"), we recommend using the scanner glass to
copy the original document onto A4 or letter-size
paper, then setting the copied document for better
results.
R
Do not set documents that do not satisfy the
requirements of size and weight. Make a copy of the
document using the scanner glass and set the copy.
R
Available document size, document weight and
effective scanning area are as follows:
For assistance, please visit http://www.panasonic.com/help
25
2. Preparation