Philips HDRW720 User manual - Page 19

Preparing the remote control for operation, Using your DVD-Recorder remote control with your TV set - dvd recorder manual

Page 19 highlights

ENGLISH Connecting the DVD recorder Preparing the remote control for operation The remote control and its batteries are packed separately in the original DVD recorder packaging. You must install the batteries in the remote control before use - described in the following section. 1 Take the remote control and the enclosed batteries (2 batteries). 2 Open the battery compartment, insert the batteries as shown and then close the battery compartment. Match the polarities (+ and -) on the batteries with the diagram on the remote. The remote control is now ready to use. Its range is approximately 5 to 10 meters. 'Aim' correctly Aim the remote control at the DVD recorder and not at the TV set. Using your DVD Recorder remote control with your TV set With the enclosed multicode remote control you can control the main functions of your TV set. To do this, you must first enter a code number that corresponds to the make of your TV set. You will find a summary of all available remote control codes on the last page of this manual. For the following functions you need to hold down the • TV button (on the left side) and then select the function you need with the appropriate button. TV/MUTE y switch off sound STANDBY m switch off the TV set CHANNEL q next channelr CHANNEL r previous channelr Additionally on Philips TV-sets: T/C switch Teletext (TXT) on/off TIMER s Clock display on the screen on/off RETURN To return to the previous menu step SYSTEM MENU Call up the System Menu from the TV B , A In the menus cursor up/down D , C In the menus cursor left/right OK Confirm functions or settings Color buttons Buttons for special functions TUNER Switchng the TV from the external jacks to the internal tuner (TV channels). Connecting to the antenna To receive TV programs you have to connect the DVD-recorder to the antenna or the cable network. 1 Switch off your TV set. 2 Remove the antenna or cable TV signal from your TV. Insert it into the ANTENNA IN jack at the back of the DVD Recorder. 3 Insert one end of the supplied antenna cable into the TV OUT jack at the back of the DVD Recorder and the other end into the antenna input jack at the back of the TV. The TV's Antenna In jack may be labeled ANT IN, RF IN, 75 ohm, etc. Check your TV instructions for details. 1 Hold down the STANDBY m button. 2 Using the number buttons 0..9 , enter the code number that corresponds to the make (manufacturer) of your TV set. 3 When you have entered the code number check, that the TV set will responds to the TV VOLUME r or TV VOLUME q buttons. a My TV set will not react b Also try to enter the other code numbers or that of other manufacturers. b In some cases, it is possible that your TV set will not react to the selected code numbers. If this is the case, you unfortunately cannot use this function. 4 You can select one of the following functions: TV VOLUME q increase the TV volume TV VOLUME r decrease the TV volume 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90

12
Preparing the remote control for
operation
The remote control and its batteries are packed separately in the
original DVD recorder packaging. You must install the batteries in the
remote control before use - described in the following section.
1
Take the remote control and the enclosed batteries (2 batteries).
2
Open the battery compartment, insert the batteries as shown and
then close the battery compartment. Match the polarities (+ and -)
on the batteries with the diagram on the remote.
The remote control is now ready to use.
Its range is approximately 5 to 10 meters.
'Aim' correctly
Aim the remote control at the DVD recorder and not at the TV set.
Using your DVD±Recorder remote control
with your TV set
With the enclosed multicode remote control you can control the main
functions of your TV set. To do this, you must first enter a code
number that corresponds to the make of your TV set.
You will find a summary of all available remote control codes on the
last page of this manual.
1
Hold down the
STANDBY
m
button.
2
Using the number buttons
0..9
, enter the code number that
corresponds to the make (manufacturer) of your TV set.
3
When you have entered the code number check, that the TV set
will responds to the
TV VOLUME
r
or
TV
VOLUME
q
buttons.
a
My TV set will not react
b
Also try to enter the other code numbers or that of other
manufacturers.
b
In some cases, it is possible that your TV set will not react to the
selected code numbers. If this is the case, you unfortunately cannot
use this function.
4
You can select one of the following functions:
TV VOLUME
q
increase the TV volume
TV VOLUME
r
decrease the TV volume
For the following functions you need to hold down the
TV
button (on the left side) and then select the function you need
with the appropriate button.
TV/MUTE
y
switch off sound
STANDBY
m
switch off the TV set
CHANNEL
q
next channelr
CHANNEL
r
previous channelr
Additionally on Philips TV-sets:
T/C
switch Teletext (TXT) on/off
TIMER
s
Clock display on the screen on/off
RETURN
To return to the previous menu step
SYSTEM MENU
Call up the System Menu from the TV
B
,
A
In the menus cursor up/down
D
,
C
In the menus cursor left/right
OK
Confirm functions or settings
Color buttons
Buttons for special functions
TUNER
Switchng the TV from the external jacks to
the internal tuner (TV channels).
Connecting to the antenna
To receive TV programs you have to connect the DVD-recorder to
the antenna or the cable network.
1
Switch off your TV set.
2
Remove the antenna or cable TV signal from your TV. Insert it into
the
ANTENNA IN
jack at the back of the DVD Recorder.
3
Insert one end of the supplied antenna cable into the
TV
OUT
jack at the back of the DVD Recorder and the other end
into the antenna input jack at the back of the TV.
The TV's Antenna In jack may be labeled ANT IN, RF IN, 75 ohm,
etc. Check your TV instructions for details.
ENGLISH
Connecting the DVD recorder