Ricoh P 311 Users Guide - Page 154

Select [Job Reset] to cancel, See Loading Paper.

Page 154 highlights

7. Troubleshooting Message Check Paper Type #: Job: Cover open Update Firmware Unknown Error Indep.Sply.Prt.Cart. Out of Paper: # Low voltg stopped print Explanation Recommended Action The paper type setting in the tray # (1, 2, bypass) differs from that of actual paper type in the tray. Load paper of the selected type in the tray, and then select [Form Feed] to continue printing. Select [Job Reset] to cancel printing. The top or front cover is open. Open and then close the top or front cover. Controller FW could not be downloaded. Turn off the main power, turn it back on, and then download the controller FW again. If the download fails again, contact your sales or service representative. A non-supported print cartridge is installed. Replace the toner to an appropriate one. See page 141 "Replacing the Print Cartridge". If the error message appears even though the toner cartridge is attached correctly, use a dry cloth to wipe the part of the toner cartridge that is in contact with the machine. The indicated tray # (1, 2, bypass) is out of paper. Load paper into the indicated paper tray. See page 26 "Loading Paper". The supplied voltage is too low to run the machine's functions. Check the power source. If devices that consume much electricity, such as halogen heaters or electric heaters, are connected to the same outlet as the machine, plug them into separate outlets. 152

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220

Message
Explanation
Recommended Action
Check Paper Type
#:
Job:
The paper type setting in the
tray # (1, 2, bypass) differs
from that of actual paper type in
the tray.
Load paper of the selected type
in the tray, and then select
[Form Feed] to continue
printing.
Select [Job Reset] to cancel
printing.
Cover open
The top or front cover is open.
Open and then close the top or
front cover.
Update Firmware Unknown
Error
Controller FW could not be
downloaded.
Turn off the main power, turn it
back on, and then download
the controller FW again.
If the download fails again,
contact your sales or service
representative.
Indep.Sply.Prt.Cart.
A non-supported print cartridge
is installed.
Replace the toner to an
appropriate one. See
page 141 "Replacing the Print
Cartridge".
If the error message appears
even though the toner cartridge
is attached correctly, use a dry
cloth to wipe the part of the
toner cartridge that is in contact
with the machine.
Out of Paper: #
The indicated tray # (1, 2,
bypass) is out of paper.
Load paper into the indicated
paper tray.
See page 26 "Loading Paper".
Low voltg stopped print
The supplied voltage is too low
to run the machine's functions.
Check the power source. If
devices that consume much
electricity, such as halogen
heaters or electric heaters, are
connected to the same outlet as
the machine, plug them into
separate outlets.
7. Troubleshooting
152