Ryobi GD201 Operation Manual - Page 46

Programming The Outdoor Keypad

Get Ryobi GD201 PDF manuals and user guides View all Ryobi GD201 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

OPERATION PROGRAMMING THE OUTDOOR KEYPAD See Figures 81 - 82. WARNING: Keep moving door in sight when using outdoor keypad. Contact with moving door can cause DEATH or serious injury. Program Once you begin programming the outdoor keypad, you have two minutes to complete each step. If a step is not completed within two minutes, programming information will be erased. For best results, stand beneath the garage door opener when programming the keypad.  If you haven't already done so, install a 9-volt battery into the outdoor keypad.  Press and hold the 1 button. With the 1 button still depressed, press the ON/PROGRAM button then release both. The LEDs on the keypad will flash two times and then remain lit.  Enter your desired PIN (4 digits). The LEDs on the keypad will flash three times and remain lit for a few seconds. This indicates the PIN has been accepted and the keypad is ready to be paired with your garage door opener.  Press and hold the PROGRAM button on the garage door opener's console until the garage door opener's LED lights turn off and the light behind the PROGRAM button on the console flashes three times. This indicates the console is in programming mode. NOTE: It may take several seconds for lights to flash.  Press the ON/PROGRAM button on the outdoor keypad, then enter your PIN. The light behind the PROGRAM button on the garage door opener's console will flash three times, then the garage door opener's LED lights will turn on. NOTE: It may take several seconds for lights to flash.  Within 30 seconds after the LED lights turn on, press the 0 button on the keypad. Once the garage door moves, the set-up is complete.  To operate the garage door opener after initial set-up, press the ON/PROGRAM button on the keypad, then enter your PIN. NOTE: In order to change the PIN or reset a forgotten PIN, repeat all of the steps listed in this section, including syncing the outdoor keypad to the garage door opener. To set up a temporary PIN: It is possible to set up a temporary PIN for use by visitors or service personnel. This PIN will remain available only until the next time you enter your regular PIN on the keypad.  Press and hold the 3 button. With the 3 button still depressed, press the ON/PROGRAM button then release Console Door Fig. 81 0 Button On/Program Button Fig. 82 both. The LEDs on the keypad will flash three times and then remain lit.  Enter your current PIN. The LEDs on the keypad will briefly flash twice.  Enter the desired temporary PIN. The LEDs on the keypad will briefly flash three times and the temporary PIN is now ready to use.  To operate the garage door opener using the temporary PIN, press the ON/PROGRAM button on the keypad, then enter the temporary PIN. NOTE: Remember that the temporary PIN will be automatically deleted the next time your regular PIN is entered on the outdoor keypad. 46 - English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
46 - English
PROGRAMMING THE OUTDOOR KEYPAD
See Figures 81 - 82.
WARNING:
Keep moving door in sight when using outdoor keypad.
Contact with moving door can cause DEATH or serious
injury.
Once you begin programming the outdoor keypad, you
have two minutes to complete each step. If a step is not
completed within two minutes, programming information
will be erased. For best results, stand beneath the garage
door opener when programming the keypad.
If you haven’t already done so, install a 9-volt battery into
the outdoor keypad.
Press and hold the
1
button. With the
1
button still
depressed, press the
ON/PROGRAM
button then release
both. The LEDs on the keypad will flash two times and
then remain lit.
Enter your desired PIN (4 digits). The LEDs on the keypad
will flash three times and remain lit for a few seconds. This
indicates the PIN has been accepted and the keypad is
ready to be paired with your garage door opener.
Press and hold the
PROGRAM
button on the garage
door opener’s console until the garage door opener’s
LED lights turn off and the light behind the
PROGRAM
button on the console flashes three times. This indicates
the console is in programming mode.
NOTE:
It may take several seconds for lights to flash.
Press the
ON/PROGRAM
button on the outdoor keypad,
then enter your PIN. The light behind the
PROGRAM
button on the garage door opener’s console will flash
three times, then the garage door opener’s LED lights
will turn on.
NOTE:
It may take several seconds for lights to flash.
Within 30 seconds after the LED lights turn on, press the
0
button on the keypad. Once the garage door moves,
the set-up is complete.
To operate the garage door opener after initial set-up,
press the
ON/PROGRAM
button on the keypad, then
enter your PIN.
NOTE:
In order to change the PIN or reset a forgotten PIN,
repeat all of the steps listed in this section, including syncing
the outdoor keypad to the garage door opener.
To set up a temporary PIN:
It is possible to set up a temporary PIN for use by visitors or
service personnel. This PIN will remain available only until
the next time you enter your regular PIN on the keypad.
Press and hold the
3
button. With the
3
button still
depressed, press the
ON/PROGRAM
button then release
0 Button
On/Program
Button
Program
Console
Door
Fig. 82
Fig. 81
OPERATION
both. The LEDs on the keypad will flash three times and
then remain lit.
Enter your current PIN. The LEDs on the keypad will briefly
flash twice.
Enter the desired temporary PIN. The LEDs on the keypad
will briefly flash three times and the temporary PIN is now
ready to use.
To operate the garage door opener using the temporary
PIN, press the
ON/PROGRAM
button on the keypad,
then enter the temporary PIN.
NOTE:
Remember that the temporary PIN will be automatically
deleted the next time your regular PIN is entered on the
outdoor keypad.