Schwinn 810 Treadmill Service Manual - Page 126

Attach the new Speed Sensor Connector to the Motor Control Board.

Get Schwinn 810 Treadmill PDF manuals and user guides View all Schwinn 810 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 126 highlights

10. Using a #2 Phillips screwdriver, remove the 2 indicated screws (by arrow) that attach the Speed Sensor to the Frame near the Drive Pulley. Note: Be sure to observe the distance from the Speed Sensor to the Drive Pulley. This distance affects the effectiveness of the Speed Sensor and will be used for the re-assembly process. 11. Remove the Speed Sensor Cable from the Clips that secure it to the Frame. Speed Sensor Drive Belt Drive Pulley Speed Sensor 12. Remove the Speed Sensor Connector from the Motor Control Board. Note: See following page for Wiring Diagram and close up image of Motor Control Board. Speed Sensor Clips 13. Attach the new Speed Sensor Connector to the Motor Control Board. 14. Route the new Speed Sensor Cable along the Frame and secure it with the Speed Sensor Clips. 15. Using a #2 Phillips screwdriver, attach the new Speed Sensor and adjust it to be the same distance as the old Sensor from the Drive Pulley. 16. Re-install all remaining parts that were removed in reverse order. 17. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner's Manual. 126

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
126
10. Using a #2 Phillips screwdriver, remove the 2 indicated screws (by arrow) that
attach the Speed Sensor to the Frame near the Drive Pulley.
Note:
Be sure to observe the distance from the Speed Sensor to the Drive Pulley.
This distance affects the effectiveness of the Speed Sensor and will be used for
the re-assembly process.
11. Remove the Speed Sensor Cable from the Clips that secure it to the Frame.
12. Remove the Speed Sensor Connector from the Motor Control Board.
Note:
See following page for Wiring Diagram and close up image of Motor Control Board.
13. Attach the new Speed Sensor Connector to the Motor Control Board.
14. Route the new Speed Sensor Cable along the Frame and secure it with the Speed Sensor Clips.
15. Using a #2 Phillips screwdriver, attach the new Speed Sensor and adjust it to be the same distance as the old Sensor from the Drive Pulley.
16. Re-install all remaining parts that were removed in reverse order.
17. Final Inspection
Inspect your machine to ensure that all hardware is tight and components are properly assembled.
Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner’s
Manual.
Drive Belt
Speed
Sensor
Drive Pulley
Speed Sensor Clips
Speed Sensor