Schwinn 810 Treadmill Service Manual - Page 17
Service Mode Procedures
 |
View all Schwinn 810 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 17 highlights
Service Mode Procedures PROCEDURE 1: CALIBRATE MCB: 1. Stand next to the machine where the Console can easily be reached. Be sure the area around the Treadmill is clear of all bystanders, children and pets. Be sure there is nothing on or under the Walking Belt, or near the Treadmill. 2. Push and hold down the Pause/Stop and Enter buttons until the machine enters engineering mode 3. Push the Start button 8 times. 4. The calibration procedure will begin by automatically moving the Walking Belt and adjusting the incline of the Walking Deck for about a minute. Then the console will flash and beep. Be sure not to touch or allow anyone else to touch the machine while calibration is occurring. 5. Procedure is now complete. 17
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12 -
13 -
14 -
15 -
16 -
17 -
18 -
19 -
20 -
21 -
22 -
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
 |
 |
17
Service Mode Procedures
PROCEDURE 1: CALIBRATE MCB:
1. Stand next to the machine where the Console can easily be reached.
Be sure the area around the Treadmill is clear of all bystanders, children and pets. Be sure there is nothing on or under the
Walking Belt, or near the Treadmill.
2. Push and hold down the Pause/Stop and Enter buttons until the machine enters engineering mode
3. Push the Start button 8 times.
4. The calibration procedure will begin by automatically moving the Walking Belt and adjusting the incline of the Walking Deck for about a minute.
Then the console will flash and beep.
Be sure not to touch or allow anyone else to touch the machine while calibration is occurring.
5. Procedure is now complete.