Schwinn 810 Treadmill Service Manual - Page 87

Be sure not to touch the walking belt or step on the power cord.

Get Schwinn 810 Treadmill PDF manuals and user guides View all Schwinn 810 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

35. Slightly push the walking deck forward toward the console. With your foot lightly push the top part of the hydraulic lift forward until the locking tube releases and you can pull the walking deck away from the console. Hold up the rear of the walking deck, and move to the side of the machine. Keep clear of the movement path of the walking deck. 36. The hydraulic lift is set up to drop gradually. Hold onto the walking deck until approximately 2/3 of the movement down. Lower the weight with your legs. Be aware that the walking deck can possibly drop quickly in the last part of the movement. If you used spray lubricant, wait 5 minutes before turning on power to the machine to allow the aerosol to dissipate. 37. Attach the power cord and turn on the Treadmill by flipping the power switch to ON. 38. Start the belt at the slowest speed and stand well behind the machine. Let the belt operate for approximately 15 seconds. Notice if the Walking Belt needs to be adjusted so it runs centered on the machine. Be sure not to touch the walking belt or step on the power cord. Keep bystanders, children and pets away from the machine you are servicing at all times. 39. If the Walking Belt needs to be adjusted, use a 6mm hex wrench on the side the belt should move away from and rotate the Adjustment Bolt a 1/4 turn clock-wise. 40. Allow the Walking Belt to adjust to the new tension by allowing it to run a couple seconds. 41. Repeat steps 39 and 40 until the Walking Belt is centered. 42. Switch off your machine. 43. Take care to clean up any excess lubricant from the deck. Adjustment Bolt To decrease the possibility of slipping, be sure the deck area is free from grease or oil. Clean off any excess oil from the machine surfaces. Adjustment Bolt 44. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner's Manual. 87

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
87
35. Slightly push the walking deck forward toward the console. With your
foot lightly push the top part of the hydraulic lift forward until the locking tube
releases and you can pull the walking deck away from the console. Hold up
the rear of the walking deck, and move to the side of the machine.
Keep clear of the movement path of the walking deck.
36. The hydraulic lift is set up to drop gradually. Hold onto the walking deck
until approximately 2/3 of the movement down. Lower the weight with your
legs. Be aware that the walking deck can possibly drop quickly in the last part
of the movement.
If you used spray lubricant, wait 5 minutes before turning on
power to the machine to allow the aerosol to dissipate.
37. Attach the power cord and turn on the Treadmill by flipping the power
switch to ON.
38. Start the belt at the slowest speed and stand well behind the machine.
Let the belt operate for approximately 15 seconds. Notice if the Walking Belt
needs to be adjusted so it runs centered on the machine.
Be sure not to touch the walking belt or step on the power cord.
Keep bystanders, children and pets away from the machine you
are servicing at all times.
39. If the Walking Belt needs to be adjusted, use a 6mm hex wrench on the
side the belt should move away from and rotate the Adjustment Bolt a 1/4
turn clock-wise.
40. Allow the Walking Belt to adjust to the new tension by allowing it to run a
couple seconds.
41. Repeat steps 39 and 40 until the Walking Belt is centered.
42. Switch off your machine.
43. Take care to clean up any excess lubricant from the deck.
To decrease the possibility of slipping, be sure the deck area is
free from grease or oil. Clean off any excess oil from the machine
surfaces.
44. Final Inspection
Adjustment Bolt
Adjustment Bolt
Inspect your machine to ensure that all hardware is tight and components are properly assembled.
Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner’s
Manual.