Schwinn 810 Treadmill Service Manual - Page 61

If you used spray lubricant, wait 5 minutes before turning

Get Schwinn 810 Treadmill PDF manuals and user guides View all Schwinn 810 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

26. Make sure there is sufficient space to lower the walking deck. Keep a minimum clearance behind the machine of 79" (2 m) and 19.7" (0.5 m) on each side. This is the recommended safe distance for access, movement and emergency dismounts from the machine. 27. Make sure there is no object on or around the treadmill to spill or cause blockage from the fully unfolded position. 28. Slightly push the walking deck forward toward the console. With your foot lightly push the top part of the hydraulic lift forward until the locking tube releases and you can pull the walking deck away from the console. Hold up the rear of the walking deck, and move to the side of the machine. Keep clear of the movement path of the walking deck. 29. The hydraulic lift is set up to drop gradually. Hold onto the walking deck until approximately 2/3 of the movement down. Lower the weight with your legs. Be aware that the walking deck can possibly drop quickly in the last part of the movement. If you used spray lubricant, wait 5 minutes before turning on power to the machine to allow the aerosol to dissipate. 30. Attach the power cord and turn on the Treadmill by flipping the power switch to ON. 31. Start the belt at the slowest speed and stand well behind the machine. Let the belt operate for approximately 15 seconds. Notice if the Walking Belt needs to be adjusted so it runs centered on the machine. Be sure not to touch the walking belt or step on the power cord. Keep bystanders, children and pets away from the machine you are servicing at all times. 32. If the Walking Belt needs to be adjusted, use a 6mm hex wrench on the side the belt should move away from and rotate the Adjustment Bolt a 1/4 turn clock-wise. 33. Allow the Walking Belt to adjust to the new tension by allowing it to run a couple seconds. 34. Repeat steps 44 and 45 until the Walking Belt is centered. 35. Switch off your machine. Adjustment Bolt 61 Adjustment Bolt

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
61
26. Make sure there is sufficient space to lower the walking deck.
Keep a minimum clearance behind the machine of 79” (2 m) and
19.7” (0.5 m) on each side. This is the recommended safe
distance for access, movement and emergency dismounts from
the machine.
27. Make sure there is no object on or around the treadmill to spill or cause
blockage from the fully unfolded position.
28. Slightly push the walking deck forward toward the console. With your
foot lightly push the top part of the hydraulic lift forward until the locking tube
releases and you can pull the walking deck away from the console. Hold up
the rear of the walking deck, and move to the side of the machine.
Keep clear of the movement path of the walking deck.
29. The hydraulic lift is set up to drop gradually. Hold onto the walking deck
until approximately 2/3 of the movement down. Lower the weight with your
legs. Be aware that the walking deck can possibly drop quickly in the last part
of the movement.
If you used spray lubricant, wait 5 minutes before turning on
power to the machine to allow the aerosol to dissipate.
30. Attach the power cord and turn on the Treadmill by flipping the power
switch to ON.
31. Start the belt at the slowest speed and stand well behind the machine.
Let the belt operate for approximately 15 seconds. Notice if the Walking Belt
needs to be adjusted so it runs centered on the machine.
Be sure not to touch the walking belt or step on the power cord.
Keep bystanders, children and pets away from the machine you
are servicing at all times.
32. If the Walking Belt needs to be adjusted, use a 6mm hex wrench on the
side the belt should move away from and rotate the Adjustment Bolt a 1/4
turn clock-wise.
33. Allow the Walking Belt to adjust to the new tension by allowing it to run a
couple seconds.
34. Repeat steps 44 and 45 until the Walking Belt is centered.
35. Switch off your machine.
Adjustment Bolt
Adjustment Bolt