Schwinn 810 Treadmill Service Manual - Page 137

Loop the Drive Belt around the Motor Pulley. Start the Drive Belt on

Get Schwinn 810 Treadmill PDF manuals and user guides View all Schwinn 810 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 137 highlights

23. Slide the old Walking Belt off of the Deck, and replace with a new Walking Belt. 24. Slide the Front Roller into the new Walking Belt in the same orientation. 25. Using a 6mm hex wrench, re-attach the Adjustment Bolt to the Rear Roller. Note: Be sure to only tighten it the number of turns it took to loosen the Walking Belt. 26. Using a 6mm hex wrench, re-install the 2 screws to the Deck. 27. Loop the Drive Belt around the Front Roller. Insert the end of the Front Roller with the Drive Pulley into the Frame and pivot the other end into the Bracket. 28. Using a 6mm hex wrench, attach the Front Roller to the Bracket. Note: Tighten the hardware until the Front Roller is centered in the Bracket. Bracket Front Roller 29. Loop the Drive Belt around the Motor Pulley. Start the Drive Belt on the Drive Pulley and roll it in a clockwise motion. Be sure the Belt does not come off of the Motor Pulley. Keep fingers out of any pinch opportunities when turning the Pulleys. 30. Roll the Drive Pulley clockwise until the Drive Belt is fully installed. Continue to roll the Belt forward while adding side pressure with fingers to align as necessary. 31. Inspect the Speed Sensor to see if it has been moved during the procedure. If necessary, adjust it to be the appropriate distance from the Drive Pulley. 137 Speed Sensor Assembly Drive Pulley Motor Pulley

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
137
Bracket
Front Roller
23. Slide the old Walking Belt off of the Deck, and replace with a new Walk-
ing Belt.
24. Slide the Front Roller into the new Walking Belt in the same orientation.
25. Using a 6mm hex wrench, re-attach the Adjustment Bolt to the Rear
Roller.
Note:
Be sure to only tighten it the number of turns it took to loosen the
Walking Belt.
26. Using a 6mm hex wrench, re-install the 2 screws to the Deck.
27. Loop the Drive Belt around the Front Roller. Insert the end of the Front
Roller with the Drive Pulley into the Frame and pivot the other end into the
Bracket.
28. Using a 6mm hex wrench, attach the Front Roller to the Bracket.
Note:
Tighten the hardware until the Front Roller is centered in the Bracket.
29. Loop the Drive Belt around the Motor Pulley. Start the Drive Belt on the
Drive Pulley and roll it in a clockwise motion. Be sure the Belt does not come
off of the Motor Pulley.
Keep fingers out of any pinch opportunities when turning the
Pulleys.
30. Roll the Drive Pulley clockwise until the Drive Belt is fully installed. Con-
tinue to roll the Belt forward while adding side pressure with fingers to align
as necessary.
31. Inspect the Speed Sensor to see if it has been moved during the pro-
cedure. If necessary, adjust it to be the appropriate distance from the Drive
Pulley.
Drive Pulley
Motor Pulley
Speed Sensor Assembly