Schwinn 810 Treadmill Service Manual - Page 92

Be sure not to touch or allow anyone else

Get Schwinn 810 Treadmill PDF manuals and user guides View all Schwinn 810 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

11. Using a #2 Phillips screwdriver, remove the 4 indicated screws that attach the Motor Control Board (MCB) to the Frame. 12. Remove old Motor Control Board, and install the new Motor Control Board. Connect all the cables to the MCB in their proper locations. Be sure not to pinch or cut the cables. 13. Re-install all remaining parts that were removed in reverse order. 14. Attach the power cord and turn on the Treadmill by flipping the power switch to ON. 15. Stand next to the machine where the Console can easily be reached. Be sure the area around the Treadmill is clear of all bystanders, children and pets. Be sure there is nothing on or under the Walking Belt, or near the Treadmill. 16. Push and hold down the Pause/Stop and Enter buttons until machine enters engineering mode. 17. Push the Start button 8 times. 18. The calibration procedure will begin by automatically moving the Walking Belt and adjusting the incline of the Walking Deck for about a minute. Then the console will flash and beep. Be sure not to touch or allow anyone else to touch the machine while calibration is occurring. USER MANUAL HR ZONES Max 100% Anaerobic 80-90% Aerobic 70-80% MANUAL GOALS WEIGHT LOSS INTERVALS HEART RATE CUSTOM Fat Burn 50-70% Warm Up 50% GOALS PROGRAMS WEIGHT LOSS INTERVALS HEART RATE CUSTOM 10 8 6 4 2 Enter button 19. The calibration procedure is now complete. Start button Pause/Stop button 20. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner's Manual. 92

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
92
11. Using a #2 Phillips screwdriver, remove the 4 indicated screws that
attach the Motor Control Board (MCB) to the Frame.
12. Remove old Motor Control Board, and install the new Motor Control
Board. Connect all the cables to the MCB in their proper locations. Be
sure not to pinch or cut the cables.
13. Re-install all remaining parts that were removed in reverse order.
14. Attach the power cord and turn on the Treadmill by flipping the power
switch to ON.
15. Stand next to the machine where the Console can easily be reached.
Be sure the area around the Treadmill is clear of all bystanders, children and pets. Be sure there is nothing on or under the Walking
Belt, or near the Treadmill.
4
2
6
8
10
Max
100%
Anaerobic
80-90%
Aerobic
70-80%
Fat Burn
50-70%
Warm Up
50%
USER
PROGRAMS
MANUAL
GOALS
WEIGHT
LOSS
INTERVALS
HEART
RATE
CUSTOM
HR ZONES
MANUAL
GOALS
WEIGHT LOSS
INTERVALS
HEART RATE
CUSTOM
Enter
button
Pause/Stop button
Start button
16. Push and hold down the Pause/Stop and Enter
buttons until machine enters engineering mode.
17. Push the Start button 8 times.
18. The calibration procedure will begin by auto-
matically moving the Walking Belt and adjusting the
incline of the Walking Deck for about a minute.
Then the console will flash and beep.
Be sure not to touch or allow anyone else
to touch the machine while calibration is
occurring.
19. The calibration procedure is now complete.
20. Final Inspection
Inspect your machine to ensure that all hardware is tight and components are properly assembled.
Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner’s
Manual.