Schwinn 810 Treadmill Service Manual - Page 145

If you used spray lubricant, wait 5 minutes before turning on power to the machine to allow

Get Schwinn 810 Treadmill PDF manuals and user guides View all Schwinn 810 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 145 highlights

23. Slide the old Walking Deck Assembly out of the Walking Belt, and flip over so the Walking Belt Guides are exposed. 24. Using a #2 Phillips screwdriver, remove the Walking Belt Guides and attach them to the new Walking Deck in the same orientation. 25. Turn over the new Walking Deck Assembly, and replace it between the Walking Belt in the same orientation. 26. Using a 6mm hex wrench, re-install the 4 screws to the Deck. Walking Deck Walking Belt Guides 27. Re-install all remaining parts that were removed in reverse order. 28. Inspect the surface material below the Treadmill. If the surface material is difficult to clean or could be damaged by silicone lubricant, place absorbent material (such as cardboard or newspaper) below the length of the Walking Deck. 29. Apply a few drops of the lubricant on the deck below the belt. Carefully lift the belt and apply a few drops of the lubricant the entire width of the belt. A very thin layer of silicone lubricant on the entire deck below the belt is desired. NOTICE: Always use a 100% pure silicone lubricant. Do not use a degreaser like WD-40® as this could seriously impact performance. We can recommend that you use the following: • 100% pure silicone, available at most hardware and auto parts stores. • Lube-N-Walk® Treadmill Lubrication Kit, available from your local specialty fitness dealer or Nautilus, Inc. Silicone lubricant is not intended for human consumption. Keep out of reach of children. Store in a safe place. 30. Manually rotate the belt 1/2 of the length of the belt and apply lubricant again. If you used spray lubricant, wait 5 minutes before turning on power to the machine to allow the aerosol to dissipate. 31. Connect the power cord back into the machine and then into the wall outlet. 32. Turn on the power to the machine with the power switch. 33. Stay to one side of your machine and start the belt at the slowest speed. Let the belt operate for approximately 15 seconds. Be sure not to touch the walking belt or step on the power cord. Keep bystanders and children away from the product you are servicing at all times. 145

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
145
23. Slide the old Walking Deck Assembly out of the Walking Belt, and flip
over so the Walking Belt Guides are exposed.
24. Using a #2 Phillips screwdriver, remove the Walking Belt Guides and
attach them to the new Walking Deck in the same orientation.
25. Turn over the new Walking Deck Assembly, and replace it between the
Walking Belt in the same orientation.
26. Using a 6mm hex wrench, re-install the 4 screws to the Deck.
27. Re-install all remaining parts that were removed in reverse order.
Walking Deck
Walking Belt
Guides
28. Inspect the surface material below the Treadmill. If the surface material is difficult to clean or could be damaged by silicone lubricant, place
absorbent material (such as cardboard or newspaper) below the length of the Walking Deck.
29. Apply a few drops of the lubricant on the deck below the belt. Carefully lift the belt and apply a few drops of the lubricant the entire width of the
belt. A very thin layer of silicone lubricant on the entire deck below the belt is desired.
NOTICE:
Always use a 100% pure silicone lubricant. Do not use a degreaser like WD-40
®
as this could seriously impact performance. We can
recommend that you use the following:
• 100% pure silicone, available at most hardware and auto parts stores.
• Lube-N-Walk
®
Treadmill Lubrication Kit, available from your local specialty fitness dealer or Nautilus, Inc.
Silicone lubricant is not intended for human consumption. Keep out of reach of children. Store in a safe place.
30. Manually rotate the belt 1/2 of the length of the belt and apply lubricant again.
If you used spray lubricant, wait 5 minutes before turning on power to the machine to allow the aerosol to dissipate.
31. Connect the power cord back into the machine and then into the wall outlet.
32. Turn on the power to the machine with the power switch.
33. Stay to one side of your machine and start the belt at the slowest speed. Let the belt operate for approximately 15 seconds.
Be sure not to touch the walking belt or step on the power cord. Keep bystanders and children away from the product you are
servicing at all times.