Symantec 16-00-00091 Installation Guide - Page 26

To connect the cables, Installation, Symantec Firewall/VPN 200 front panel

Get Symantec 16-00-00091 - FNC XGRD FW VPN 200 PDF manuals and user guides
UPC - 037648211703
View all Symantec 16-00-00091 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Installation After the install is successful with a single computer, you can then add additional computers and/or hubs to the Symantec Firewall/VPN. The following installation assumes this simple network setup. Modem (WAN) 10 BaseT Ports LAN Ports LAN Link LEDs Figure 2-1: Symantec Firewall/VPN 200 front panel 9v DC Power Input Power Switch Figure 2-2: Symantec Firewall/VPN 200 back panel To connect the cables 1. Insert the 9v DC 1000 mA power adapter that was included with the Symantec Firewall/ VPN and plug it into an electrical outlet. Make sure to ONLY use the adapter that came with the unit. 2. Remove the cable that came with your modem from your computer (if applicable) and insert the free end into the modem (WAN) port of the Symantec Firewall/VPN. You should see the WAN link light illuminate green. If not, check that you are using the same cable that came with the modem. For the Symantec Firewall/VPN 200: Repeat this step for each additional modem port with a separate modem or connection (you can mix cable, DSL, or routed connections on the two modem ports). 2-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
2-4
Installation
After the install is successful with a single computer, you can then add additional computers and/or
hubs to the Symantec Firewall/VPN. The following installation assumes this simple network setup.
Figure 2-1: Symantec Firewall/VPN 200 front panel
Figure 2-2: Symantec Firewall/VPN 200 back panel
To connect the cables
1.
Insert the 9v DC 1000 mA power adapter that was included with the Symantec Firewall/
VPN and plug it into an electrical outlet. Make sure to ONLY use the adapter that came
with the unit.
2.
Remove the cable that came with your modem from your computer (if applicable) and
insert the free end into the modem (WAN) port of the Symantec Firewall/VPN. You
should see the WAN link light illuminate green. If not, check that you are using the same
cable that came with the modem.
For the Symantec Firewall/VPN 200: Repeat this step for each additional modem port
with a separate modem or connection (you can mix cable, DSL, or routed connections on
the two modem ports).
Modem (WAN)
10 BaseT Ports
LAN Ports
LAN Link LEDs
9v DC
Power Input
Power Switch