Symantec 16-00-00091 Installation Guide - Page 68

Expert Level - SNMP Trap Receiver fields, Expert Level - Remote Access IP Range fields

Get Symantec 16-00-00091 - FNC XGRD FW VPN 200 PDF manuals and user guides
UPC - 037648211703
View all Symantec 16-00-00091 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Advanced Configuration Expert Level - SNMP Trap Receiver section fields Sets the IPs to receive the trap alerts from the unit. Expert Level - Remote Access IP Range section fields The Symantec Firewall/VPN's web interface can be accessed remotely from a range of IP addresses. For security reasons, Symantec recommends that all external remote management be done through a VPN tunnel. When using a VPN tunnel, simply point your growser to the internal IP address of the Symantec Firewall/VPN. To remotely configure the unit, enter the start and end IP range (enter the same value for both if it's a single IP). You can then access the unit from an external web browser by entering the WAN port IP followed by port 8088. For example: type "http://207.158.227.235:8088" into your external browser if 207.158.227.235 was the address obtained from your ISP by the Symantec Firewall/VPN. You must be accessing from the IP range specified. Also, you should set the Configuration Password for security. Allow Remote Upgrade You can Enable Allow Remote Upgrade if you wish to remotely perform TFTP upgrades to the unit's firmware from the above IP range. The default is Disabled. 4-28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
4-28
Advanced Configuration
Expert Level - SNMP Trap Receiver section fields
Sets the IPs to receive the trap alerts from the unit.
Expert Level - Remote Access IP Range section fields
The Symantec Firewall/VPN's web interface can be accessed remotely from a range of IP
addresses. For security reasons, Symantec recommends that all external remote management be
done through a VPN tunnel.
When using a VPN tunnel, simply point your growser to the internal
IP address of the Symantec Firewall/VPN.
To remotely configure the unit, enter the start and end IP range (enter the same value for both if it's
a single IP).
You can then access the unit from an external web browser by entering the WAN port
IP followed by port 8088.
For example: type "http://207.158.227.235:8088" into your external browser if 207.158.227.235
was the address obtained from your ISP by the Symantec Firewall/VPN.
You must be accessing
from the IP range specified.
Also, you should set the Configuration Password for security.
Allow Remote Upgrade
You can Enable
Allow Remote Upgrade
if you wish to remotely perform TFTP upgrades to the
unit's firmware from the above IP range. The default is
Disabled
.