TP-Link TD-W8968 TD-W8968 V1 User Guide - Page 54

Wireless Security, TD-W8968, Step 1, Wireless - lights

Get TP-Link TD-W8968 PDF manuals and user guides View all TP-Link TD-W8968 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

TD-W8968 300Mbps Wireless N USB ADSL2+ Modem Router User Guide Step 1: On the client device, enter the PIN number listed on the Modem Router's Wi-Fi Protected Setup screen. (It is also labeled on the bottom of the Modem Router.) Step 2: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup process. Step 3: When the WPS LED is on, the client device has successfully connected to the Modem Router. Step 4: Refer back to your client device or its documentation for further instructions. ) Note: 1) The WPS LED on the Modem Router will light green for five minutes if the device has been successfully added to the network. 2) The WPS function cannot be configured if the Wireless Function of the Modem Router is disabled. Please make sure the Wireless Function is enabled before configuring the WPS. 4.6.3 Wireless Security Choose menu "Wireless"Æ" Wireless Security", you can configure the security settings of your wireless network. There are three wireless security modes supported by the Modem Router: WEP (Wired Equivalent Privacy), WPA-PSK (Pre-Shared Key), WPA2-PSK (Pre-Shared Key). Figure 4-29 ¾ Disable Wireless Security: If you do not want to use wireless security, check this radio button. But it's strongly recommended to choose one of the following modes to enable security. 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
TD-W8968
300Mbps Wireless N USB ADSL2+ Modem Router User Guide
45
Step 1:
On the client device, enter the PIN number listed on the Modem Router’s Wi-Fi
Protected Setup screen. (It is also labeled on the bottom of the Modem Router.)
Step 2:
The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected
Setup process.
Step 3:
When the WPS LED is on, the client device has successfully connected to the Modem
Router.
Step 4:
Refer back to your client device or its documentation for further instructions.
)
Note:
1)
The WPS LED on the Modem Router will light green for five minutes if the device has been
successfully added to the network.
2)
The WPS function cannot be configured if the Wireless Function of the Modem Router is
disabled. Please make sure the Wireless Function is enabled before configuring the WPS.
4.6.3 Wireless Security
Choose menu “
Wireless
”
Æ
”
Wireless Security
”, you can configure the security settings of your
wireless network.
There are three wireless security modes supported by the Modem Router: WEP (Wired Equivalent
Privacy), WPA-PSK (Pre-Shared Key), WPA2-PSK (Pre-Shared Key).
Figure 4-29
¾
Disable Wireless Security:
If you do not want to use wireless security, check this radio
button. But it’s strongly recommended to choose one of the following modes to enable
security.