Toshiba TLP-MT7 Owner's Manual - English - Page 64

Trouble indications

Get Toshiba TLP-MT7 - LCD Projector - 1000 ANSI Lumens PDF manuals and user guides
UPC - 022265950821
View all Toshiba TLP-MT7 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Maintenance 64 Trouble indications If there is some problem inside the projector, the indicators light up or blink. Control panel (Main unit side) AUTO KEYSTONE AUTO SET VOL/ADJ. ENTER EXIT MENU INPUT ON/STANDBY TEMP LAMP ON BUSY FAN Indicator ENTER MENU INPUT TEMP BUSY LAMP FAN ON/STANDBY ON EXIT KEYASUTOTONE VOL/ADJ. SAEUTTO TEMP LAMP ON BUSY ( off ) FAN Or (Lit in red) TEMP LAMP ON (Lit in red) (Lit in red) BUSY FAN The power does not come on. → Malfunction of the unit. • Unplug the power cord and call the dealer. The lamp turns off or does not light up. → The projector will return to the standby mode in about 2 minutes. If the projector does not operate normally when the power is switched on again, the lamp is at the end of its duration life or the unit has a fault. • Lamp's duration life is over, replace the lamp with a new one. 68 • Unplug the power cord and call the dealer. TEMP LAMP ON BUSY (Lit in red) FAN (Lit in green or turns off) Or Or (Lit in red) (Lit in orange)(Lit in green) TEMP LAMP ON BUSY (Lit in red) FAN The power turns off or does not come on. → The inside is too hot, or the projector has been working in an area of high temperature. • Place the projector correctly so the intake and exhaust fans' holes are not covered. • Turn the projector off, and leave it for a while, and turn it on again. • Clean the air filter. 65 * The icon appears before the power turned off. * The projector returns to the standby mode after the fault display has been shown for about 2 minutes. The power turns off or does not come on. → Trouble with the cooling fan. • Unplug the power cord and call the dealer. Or (Lit or flashing (Lit or flashing in red) in orange) * The icon appears before the power turned off. * The projector returns to the standby mode after the fault display has been shown for about 2 minutes. TEMP LAMP ON (Flashing in orange) (Lit in red) BUSY FAN The power turns off or does not come on. → The lamp cover is not properly attached. • Unplug the power cord and reattach the lamp cover. 69 * The icon appears before the power turned off. * The projector returns to the standby mode after the fault display has been shown for about 2 minutes. Notes • If abnormality occurs while operating, unplug the power cord. • When reinserting the power cord before the lamp has cooled, please wait until the lamp has cooled sufficiently before use. When the lamp is at a high temperature, it may not light and the duration life will be shortened.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
64
Maintenance
If there is some problem inside the projector,
the indicators light up or blink.
Trouble indications
Indicator
TEMP
LAMP
ON
FAN
TEMP
LAMP
ON
BUSY
FAN
TEMP
LAMP
ON
BUSY
FAN
TEMP
LAMP
ON
BUSY
FAN
TEMP
LAMP
ON
BUSY
FAN
TEMP
LAMP
ON
BUSY
( off )
TEMP
LAMP
ON
BUSY
FAN
TEMP
LAMP
ON
BUSY
FAN
TEMP
LAMP
ON
BUSY
FAN
TEMP
LAMP
ON
BUSY
FAN
Or
(Lit in red)
(Lit in red) (Lit in red)
(Lit in red)
(Lit in red)
(Lit in red)
(Lit in green or
turns off)
Or
Or
(Lit in red)
(Lit in orange)
(Flashing in orange)
(Lit in green)
Or
(Lit or flashing
in red)
(Lit or flashing
in orange)
TEMP
LAMP
ON
BUSY
FAN
ON/STANDBY
KEYSTONE
SET
AUTO
AUTO
EXIT
ENTER
MENU
INPUT
VOL/ADJ.
The power does not come on.
→
Malfunction of the unit.
•
Unplug the power cord and call the dealer.
The lamp turns off or does not light up.
→
The projector will return to the standby mode in about 2 minutes. If the
projector does not operate normally when the power is switched on again,
the lamp is at the end of its duration life or the unit has a fault.
•
Lamp’s duration life is over, replace the lamp with a new one.
•
Unplug the power cord and call the dealer.
The power turns off or does not come on.
→
The inside is too hot, or the projector has been working in an area of high
temperature.
•
Place the projector correctly so the intake and exhaust fans’ holes are not covered.
•
Turn the projector off, and leave it for a while, and turn it on again.
•
Clean the air filter.
65
*
The icon
appears before the power turned off.
*
The projector returns to the standby mode after the fault display has been
shown for about 2 minutes.
The power turns off or does not come on.
→
Trouble with the cooling fan.
•
Unplug the power cord and call the dealer.
*
The icon
appears before the power turned off.
*
The projector returns to the standby mode after the fault display has been
shown for about 2 minutes.
The power turns off or does not come on.
→
The lamp cover is not properly attached.
•
Unplug the power cord and reattach the lamp cover.
69
*
The icon
appears before the power turned off.
*
The projector returns to the standby mode after the fault display has been
shown for about 2 minutes.
Control panel
(Main unit side)
68
Notes
•
If abnormality occurs while operating, unplug the power cord.
•
When reinserting the power cord before the lamp has cooled, please wait until the lamp has cooled sufficiently before
use. When the lamp is at a high temperature, it may not light and the duration life will be shortened.