Brother International BAS-375E Programmer Instruction Manual - English - Page 51

of the pattern., lines for a multiple stitch.

Get Brother International BAS-375E PDF manuals and user guides View all Brother International BAS-375E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Chapter 2 Programming with Help Function 2. Select with and press . 3. Move the work clamp with . Press when the needle point is at point q of the pattern. The first stitch (point q) is programmed. 4. Select with and press . 5. Input the stitch length and the number of lines for a multiple stitch. Press . "2.0 mm" is input for a stitch length in the example. Input "030" to make the stitch length to 3.0 mm. To switch input between the stitch length and the number of lines, use . 6. Move the work clamp with . Press when the needle point is at point w of the pattern. 7. Move the work clamp with . Press twice when the needle point is at point e of the pattern. Be sure to press twice for a split at a corner like point e. If a split is not made, the corner will be round. 8. Program the following points up to point !7 with the curve programming steps. When there is a liner section, move the needle point from the split to the next split, and press twice. In the example, a linear line is programmed between points u and o. Be sure to program a linear line also for the matched section between points @4 and @.6 By pressing 0 , the needle point is returned to the previous point. It cannot be returned beyond the previous split. By pressing 1 , the needle point is returned to the previous split. However, when the needle point is at a split, it cannot be moved. By pressing 2 , the needle point is returned to the split before the previous split. 9. Press F . Move the work clamp with . Press when the needle point is at point !8 of the pattern. 50 Programmer

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
Programmer
50
Chapter 2 Programming with Help Function
2.
Select
with
and press
.
3.
Move the work clamp with
.
Press
when the needle point is at point
q
of
the pattern.
The first stitch (point
q
) is programmed.
4.
Select
with
and press
.
5.
Input the stitch length and the number of
lines for a multiple stitch.
Press
.
"2.0 mm" is input for a stitch length in the example.
Input "030" to make the stitch length to 3.0 mm.
To switch input between the stitch length and the number of
lines, use
.
6.
Move the work clamp with
.
Press
when the needle point is at point
w
of
the pattern.
7.
Move the work clamp with
.
Press
twice when the needle point is at point
e
of the pattern.
Be sure to press
twice for a split at a corner like point
e
.
If
a split is not made, the corner will be round.
8.
Program the following points up to point
!
7
with the curve programming steps.
When there is a liner section, move the needle point from the
split to the next split, and press
twice.
In the example, a linear line is programmed between points
u
and
o
.
Be sure to program a linear line also for the matched
section between points
@4
and
@6
.
By pressing
0
, the needle point is returned to the previous
point.
It cannot be returned beyond the previous split.
By pressing
1
, the needle point is returned to the previous
split.
However, when the needle point is at a split, it cannot be
moved.
By pressing
2
, the needle point is returned to the split
before the previous split.
9.
Press
F
.
Move the work clamp with
.
Press
when the needle point
is at point
!
8
of the pattern.