Home » Brother International Manuals » Laser Printers » Brother International MFC-P2000 » Manual Viewer

Brother International MFC-P2000 Service Manual - Page 104

SCANNER INSPECTION MODE, Scanner Panel Test

UPC - 012502525394

View all Brother International MFC-P2000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

9. SCANNER INSPECTION MODE The printer incorporates a scanner inspection mode, the factory inspection program mode. The factory inspection program mode provides two types of test mode, and then each test mode supports a few test programs. Refer to the table below; Scanner panel test Line-feeding test Maintenance copy test Continuous test mode (scanner panel test / line-feeding test / maintenance copy test) Maintenance copy test N/A To enter the factory inspection program mode, you can choose one of the following; A) Turn on the power switch of the printer while pressing the Stop and Enlarge keys. B) Press the Stop and Enlarge keys after turning on the power switch of the printer. Note: Once you press any keys other than the Stop and Enlarge keys when the power is turned on, the printer cannot enter the factory inspection program mode any more unless power is turned off and the select sequence is repeated. The printer enters into Test Mode A immediately after entering the factory inspection program mode. If you want to switch between these two test modes, press the Stop key. The following sections describe the detailed operation of each test mode. 9.1 Test Mode A When the printer enters into Test Mode A, 'A' is shown on the seven-segment LED. Then, press one of the keys to select the test program as follows; Enlarge: Photo: Copy: Stop: A-1 Scanner panel test A-2 Line-feeding test A-3 Maintenance copy test Switch to Test Mode B A-1 Scanner Panel Test The scanner panel test checks the four keys, five lamps and seven-segment LED on the scanner control panel and also the document front/rear sensors. The operation of this test is as follows; 1) When the printer enters into this mode, all lamps on the scanner control panel are off. 2) When the Enlarge, Photo, Copy and Stop keys are pressed in order, each of the four Enlarge/Reduce lamps come on from left to right in order. When all of the keys are being pressed then all four lamps are ON. 3) When the four keys are recognized, the Photo lamp flashes, and each of the seven segments on the LED is turned on in sequence. IV-35

Section	Page
HL-P2000, MFC-P2000 Parts and Service Manual.pdf	130
Action 1: Check the Supplied Items	131
Action 2: Position the Machine	132
Power Supply	132
Environment	132
System Requirements for the Brother Printing Solution for Windows	132
Action 3: Install the Toner Cartridge/Drum Unit	133
Action 4: Load Paper into Your Machine	134
Action 5: Connect Your Machine to Your Computers' Parallel Interface	136
Action 6: Plug in and Turn on Your Machine	137
Printing a Test Sample Page	138
Action 7-1: Installation from CD-ROM	139
For Windows 95/98/NT4.0	139
For Windows 3.1/3.11	139
Action 7-2: Prepare the Printer Driver and the Scanner Driver for the Machine	140
For Windows 3.1	140
For Windows 95/98	140
Action 7-3: Prepare DOS for the Machine	141
How to Use the Machine in Your DOS Application Software	141
What Does Remote Printer Console Do?	142
Installing the Remote Printer Console	142
Using the Remote Printer Console Main Program	143
Using the Machine Status Monitor Program	144
Lamps and Switch for the Printing Function	145
Ready (Paper) Lamp	145
Data (Toner) Lamp	145
Drum Lamp	146
Alarm Lamp	146
Switch	146
Other Control Features	147
Copying Function	148
Copying in Standard Mode	148
To Make Settings for Each Copy	148
Photo/Text Button	149
Enlarge/Reduce Button	149
The Number of Copies	149
Error	150
Scanning Function	151
Scanning from TWAIN Compliant Applications	151
Scanning from the VISIONEER PaperPort LE Software	152
Scanning from the Unimessage Viewer Software	153
Replacing the Toner Cartridge	154
Replacing the Drum Unit	157
Alarm Indications at a Glance	160
Operator Calls for Printing Function	160
Operator Calls for Copying and Scanning Functions	162
Service Calls for the Printing Function	162
Service Calls for Copying and Scanning Functions	163
How to View the On-Line Setup Guide & User Guide	164
Machine Specifications	165
Printing	165
Copying	166
Scanning	166
Functions	166
Electrical and Mechanical	166
Regulations	167
Eng-ug.pdf	172
Chapter 1 Introduction	178
About the Guide Books	178
About your Machine	179
Machine Overview	179
System Requirements in Brother Printing Solution for Windows	180
Features	180
Operating and Storage Environment	183
Power Supply	183
Environment	183
Chapter 2 Paper Handling	185
Paper Specifications	185
Document Specifications	189
Multi-Purpose Sheet Feeder for Printing	190
Loading Paper into the Feeder	191
Two Side Printing	193
Output Tray and Paper Support Wire	194
Chapter 3 Ptint	195
Lamps and Switch	195
Ready (Paper) Lamp	195
Data (Toner) Lamp	196
Drum Lamp	196
Alarm Lamp	196
Switch	197
Other Control Features	197
Chapter 4 Copy	199
Copying in Standard Mode	199
To Make Settings for Each Copy	199
Photo/Text	200
Enlarge/Reduce	200
The Number of Copies	201
Error	202
Chapter 5 Scan	203
Scanning from TWAIN Compliant Applications	203
Scanning from the Visioneer PaperPort LE Software	204
Scanning from the Unimessage Viewer Software	205
Chapter 6 Maintenance	206
Replacing the Toner Cartridge	206
Replacing the Drum Unit	212
Cleaning the Machine	216
Cleaning the Machine Exterior	216
Cleaning the Machine Interior and Drum Unit	217
Cleaning the Scanning Unit	220
Re-Packing the Machine	221
Chapter 7 Troubleshooting	223
Alarm Indications at a Glance	223
Operator Calls for the Printing Function	223
Operator Calls for the Copying and Scanning Functions	225
Service Calls for the Printing Function	226
Service Calls for the Copying and Scanning Functions	227
Paper Jams	228
Q & A	232
Setting up the Machine Hardware	232
Setting up the Machine for Windows	232
Setting up the Machine for DOS	233
Paper Handling	234
Printing	235
Copy	236
Scan	236
Print Quality	237
Appendix	241
Printer Specifications	241
Printing	241
Copying	242
Scanning	242
Functions	243
Electrical and Mechanical	243
Parallel Interface Specifications	244
Resident Fonts	246
Bitmapped Fonts	246
Symbol Sets/Character Sets	247
HP LaseJet llP Mode	247
EPSON Mode	247
IBM Mode	247
Regulations	252
Index	258
PR99041.pdf	287
HL/MFC-P2000	288
PR99042.pdf	289
HL-1070	290
HL-820/1020/1040/1050	291
HL/MFC-P2000	292
PR99057.pdf	293

Match case Limit results 1 per page

IV-35

SCANNER INSPECTION MODE

The printer incorporates a

scanner inspection mode

, the factory inspection program

mode.

The

factory inspection program mode

provides two types of test mode, and then each

test mode supports a few test programs.

Refer to the table below;

Scanner panel test

Line-feeding test

Maintenance copy test

Continuous test mode

(scanner panel test / line-feeding test / maintenance copy test)

Maintenance copy test

N/A

To enter the factory inspection program mode, you can choose one of the following;

A) Turn on the power switch of the printer while pressing the Stop and Enlarge keys.

B) Press the Stop and Enlarge keys after turning on the power switch of the printer.

Note:

Once you press any keys other than the Stop and Enlarge keys when the power is

turned on, the printer cannot enter the factory inspection program mode any more

unless power is turned off and the select sequence is repeated.

The printer enters into Test Mode A immediately after entering the factory inspection

program mode.

If you want to switch between these two test modes, press the Stop

key.

The following sections describe the detailed operation of each test mode.

9.1

Test Mode A

When the printer enters into Test Mode A, ‘A’ is shown on the seven-segment LED.

Then, press one of the keys to select the test program as follows;

Enlarge:

A-1 Scanner panel test

Photo:

A-2 Line-feeding test

Copy:

A-3 Maintenance copy test

Stop:

Switch to Test Mode B

A-1

Scanner Panel Test

The

scanner panel test

checks the four keys, five lamps and seven-segment LED on the

scanner control panel and also the document front/rear sensors.

The operation of this test is as follows;

1) When the printer enters into this mode, all lamps on the scanner control panel are off.

2) When the Enlarge, Photo, Copy and Stop keys are pressed in order, each of the four

Enlarge/Reduce lamps come on from left to right in order.

When all of the keys are

being pressed then all four lamps are ON.

3) When the four keys are recognized, the Photo lamp flashes, and each of the seven

segments on the LED is turned on in sequence.