Dell OptiPlex 7090 Small Form Factor Service Manual - Page 47

About this task, Steps, Next steps, the processor are higher than the others

Get Dell OptiPlex 7090 Small Form Factor PDF manuals and user guides View all Dell OptiPlex 7090 Small Form Factor manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

About this task The following image indicates the location of the processor and provides a visual representation of the installation procedure. Steps 1. Ensure that the release lever on the processor socket is fully extended in the open position. 2. Align the notches on the processor with the tabs on the processor socket and place the processor in the processor socket on the system board. NOTE: Ensure that the processor-cover notch is positioned underneath the alignment post. NOTE: The pin-1 corner of the processor has a triangle that aligns with the triangle on the pin-1 corner on the processor socket. When the processor is properly seated, all four corners are aligned at the same height. If one or more corners of the processor are higher than the others, the processor is not seated properly. 3. When the processor is fully seated in the socket, pivot the release-lever down and place it under the tab on the processor cover. Next steps 1. Install the fan and heat-sink assembly. 2. Install the 2.5/3.5-inch hard-drive caddy. 3. Install the side cover. Removing and installing components 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
About this task
The following image indicates the location of the processor and provides a visual representation of the installation procedure.
Steps
1.
Ensure that the release lever on the processor socket is fully extended in the open position.
2.
Align the notches on the processor with the tabs on the processor socket and place the processor in the processor socket
on the system board.
NOTE:
Ensure that the processor-cover notch is positioned underneath the alignment post.
NOTE:
The pin-1 corner of the processor has a triangle that aligns with the triangle on the pin-1 corner on the processor
socket. When the processor is properly seated, all four corners are aligned at the same height. If one or more corners of
the processor are higher than the others, the processor is not seated properly.
3.
When the processor is fully seated in the socket, pivot the release-lever down and place it under the tab on the processor
cover.
Next steps
1.
Install the
fan and heat-sink assembly
.
2.
Install the
2.5/3.5-inch hard-drive caddy
.
3.
Install the
side cover
.
Removing and installing components
47