Denon S-5BD Owners Manual - English - Page 80

Getting Started Simple Version Connections Playback (Basic) Settings ENGLISH GBlu-ray DiscH Symptom Cause/Solution Picture freezes momentarily during playback. • The disc may not play back correctly if it is scratched or dirty. Either clean the disc or replace it. • There may be a problem with the recorded disc. Playback does not • Check whether there is condensation on the inside of the unit or start even when 1 is disc. If there is condensation, turn off the power and let the unit pressed, or starts but stand for 1 to 2 hours. stops immediately. • The disc may not play back correctly if it is scratched or dirty. Either clean the disc or replace it. • Check whether the disc has been inserted upside down. Insert the disc so that the recording surface to be played back faces downward. • Check whether a disc that cannot be played back on this unit has been inserted. Subtitles are not displayed. • Subtitles cannot be displayed for BD-Video or DVD-Video that do not contain subtitles. • Check whether the subtitles setting is set to "OFF". Wallpaper is not displayed even after the disc has been removed. • An internal error may have occurred in the unit. Set the power to standby, wait awhile, then turn the power back on. Button operation does not work. The unit fails to operate. • Operations may not be permitted by the disc. Refer to the instructions of the disc. • The protection circuit is active. In this case, disconnect the power plug from the electric outlet, wait 5 to 10 seconds and then insert it back into the outlet. The unit fails to read • The pickup lens may be dirty. Use a commercially available lens the disc. cleaner to clean the laser pickup. Avoid use of cleaners equipped with brushes, since they may scratch the lens. Angle does not switch. • If a BD-Video or DVD-Video does not record multiple angles, angle cannot be switched. Also, multiple angles may be recorded for specific scenes. Playback does not • Playback may be prohibited by the viewing restriction setting. start when the title is Check "Ratings" on the GUI menu. selected. The password for • Reset the microprocessor. rating level has been forgotten. Page - - 2 66 65 19 31 44 - 65 74 - 30 45 77 GRadioH Symptom Cause/Solution Reception fails, or there is a lot of noise or distortion. • Change the antenna orientation or position. • Separate the AM loop antenna from the unit. • Use an FM outdoor antenna. • Separate the antenna from other connection cables. GSD memory cardH Symptom Cause/Solution Unable to play back bonus view. SD memory card cannot be read. • Check that capacity on the SD memory card is 1 GB or more. • Initialize the SD memory card on this unit. • Was the SD memory card mounted while the power was turned on? Mount the SD memory card while in Standby state. • An incompatible SD memory card may have been inserted, or the recording format may not be compatible with the unit, preventing recognition. GUSB memory deviceH Symptom Cause/Solution When a USB memory device is connected, "USB" is not displayed on the GUI menu. • The set cannot recognize a USB memory device. Check the connection. • A USB memory device not conforming to mass storage class is connected. Connect a USB memory device conforming to mass storage class. • A USB memory device cannot be connected via a USB hub. Files on a USB memory device cannot be played. • Set the USB memory device format to "FAT16" or "FAT32". For details, refer to the USB memory device's operating instructions. • If the USB memory device is divided into multiple partitions, only files stored in the top partition can be played. • The file is recorded in an incompatible format. Please record it in a compatible format. • This unit cannot play back files covered by copyright protection. The sound quality is • The file being played back has a low bit rate. poor or there is noise during playback. "Connection Error" • Unable to communicate properly. Turn off the power to this unit, is displayed. unplug the USB memory device and then plug it back in. "Communication Error" is displayed. • The USB memory device is not responding. Turn off the power to this unit, unplug the USB memory device and then plug it back in. "Overcurrent" is displayed. • The USB memory device is consuming too much power. When using a USB portable hard disk that can be powered by an AC adapter, connect its AC adapter. Page 15 15 15 15 Page 19 46 19 19 Page 14 19 14 19 - 19 12 - - - - Playback (Advanced) Multizone GUI Remote Control Part Names Other Information Troubleshooting Spec. Index 76