Garmin GPSMAP 541s Owner's Manual - Page 77

Alarms and Messages, Can't ReaD Voltages That High, LimiteD To Top OF Range - parts

Get Garmin GPSMAP 541s - Marine GPS Receiver PDF manuals and user guides
UPC - 753759096045
View all Garmin GPSMAP 541s manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Frequency: 50/200 kHz (dual frequency and 1 kW), 80/200 kHz (dual beam) Depth: 2,500 ft. (762 m) (1 kW), 1,500 ft. (457 m) (dual frequency), 900 ft (274 m) (dual beam). Depth capacity is dependent on water salinity, bottom type, and other water conditions. Alarms and Messages The unit uses an on-screen message system to alert you to unit operating characteristics. When a message appears, press MENU to acknowledge the message. Accuracy Alarm-the GPS accuracy has fallen outside of the userset value. AIS: Dangerous Target-shows the MMSI (Maritime Mobile Service Identity) of the dangerous target. Alarm Clock-the alarm clock has sounded. Anchor Drag Alarm-you have drifted out of the specified distance range. Antenna Input is Shorted-a part of the antenna wiring is crimped, broken, or contacting the chassis. Arriving At [Waypoint Name]-you arrived at the destination waypoint. You can Stop Navigation when this message appears. Appendix Battery Alarm-battery voltage has fallen below the value entered in the Battery Alarm setup. Battery Voltage Is Too High-too much input voltage-the unit shuts off in 10 seconds. Decrease the input voltage to the maximum voltage allowed (or less) for your chartplotter. Boat Is Not Moving Fast Enough to Calibrate-the boat is not moving fast enough for the speed wheel to provide a valid speed. Can't Read User Card-error reading card; remove and reinsert. Contact your dealer or Garmin Product Support if the problem persists. Can't Read Voltages That High, Limited To Top Of Range-the voltage value in the Battery Alarm setup is higher than the unit can read. Can't Read Voltages That Low, Limited To Bottom Of Range-voltage value in the Battery Alarm setup is lower than the voltage where the unit automatically turns off. Can't Unlock Maps-data on the data card is not unlocked for the unit. Contact your dealer or Garmin Product Support. Can't Write User Card, Card May Be Full-error reading card; remove and reinsert. Contact your dealer or Garmin Product Support if the problem persists. GPSMAP 400/500 Series Owner's Manual 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
GPSMAP 400/500 Series Owner’s Manual
71
Appendix
frequencY:
50/200 kHz (dual frequency and 1 kW), 80/200 kHz
(dual beam)
depth:
2,500 ft. (762 m) (1 kW), 1,500 ft. (457 m) (dual frequency),
900 ft (274 m) (dual beam). Depth capacity is dependent on
water salinity, bottom type, and other water conditions.
Alarms and Messages
The unit uses an on-screen message system to alert you to unit
operating characteristics. When a message appears, press
MENU
to
acknowledge the message.
AccuracY Alarm
—the GPS accuracy has fallen outside of the user-
set value.
AIS: dangerous Target
—shows the MMSI (Maritime Mobile
Service Identity) of the dangerous target.
Alarm Clock
—the alarm clock has sounded.
Anchor drag Alarm
—you have drifted out of the specified distance
range.
Antenna Input is ShorteD
—a part of the antenna wiring is crimped,
broken, or contacting the chassis.
Arriving At [WaYpoint Name]
—you arrived at the destination
waypoint. You can
Stop Navigation
when this message appears.
batterY Alarm
—battery voltage has fallen below the value entered
in the Battery Alarm setup.
batterY Voltage Is Too High
—too much input voltage—the unit
shuts off in 10 seconds. Decrease the input voltage to the maximum
voltage allowed (or less) for your chartplotter.
boat Is Not Moving fast Enough to CaliBrate
—the boat is not
moving fast enough for the speed wheel to provide a valid speed.
Can’t ReaD User CarD
—error reading card; remove and reinsert.
Contact your dealer or Garmin Product Support if the problem
persists.
Can’t ReaD Voltages That High, LimiteD To Top OF Range
—the
voltage value in the Battery Alarm setup is higher than the unit can
read.
Can’t ReaD Voltages That Low, LimiteD To bottom OF
Range
—voltage value in the Battery Alarm setup is lower than the
voltage where the unit automatically turns off.
Can’t Unlock Maps
—data on the data card is not unlocked for the
unit. Contact your dealer or Garmin Product Support.
Can’t Write User CarD, CarD MaY be full
—error reading card;
remove and reinsert. Contact your dealer or Garmin Product Support
if the problem persists.