Gateway FX540X 8512728 - FX540 Hardware Reference Guide - Page 63

Replacing the memory card, reader

Page 63 highlights

www.gateway.com 7 If you are replacing a drive, note any jumper settings on the old drive and set the jumpers on the new drive to be the same. If you are installing a new drive, follow the manufacturer's instructions. 8 Slide the new drive into the drive bay, line up the thumbscrew hole on the drive bay with the screw hole on the drive, then slide the drive release latch toward the front of the computer to lock the drive into place. You do not need to replace the thumbscrew because it was originally installed for shipping purposes. 9 Connect the drive cables using your notes from Step 3. If you are installing a new drive, follow the manufacturer's instructions. 10 Replace the front bezel by following the instructions in "Replacing the front bezel" on page 52. 11 Replace the side panel by following the instructions in "Replacing the side panel" on page 52. Replacing the memory card reader To replace the memory card reader: 1 Remove the side panel by following the instructions in "Removing the side panel" on page 49. 2 Remove the front bezel by following the instructions in "Removing the front bezel" on page 51. 3 Disconnect the memory card reader cables, noting their locations and orientation. (You will reconnect the cables after you install the new memory card reader.) 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164

www.gateway.com
57
7
If you are replacing a drive, note any jumper settings on
the old drive and set the jumpers on the new drive to
be the same. If you are installing a new drive, follow the
manufacturer’s instructions.
8
Slide the new drive into the drive bay, line up the
thumbscrew hole on the drive bay with the screw hole
on the drive, then slide the drive release latch toward the
front of the computer to lock the drive into place. You
do not need to replace the thumbscrew because it was
originally installed for shipping purposes.
9
Connect the drive cables using your notes from Step
3
.
If you are installing a new drive, follow the
manufacturer’s instructions.
10
Replace the front bezel by following the instructions in
“Replacing the front bezel” on page 52
.
11
Replace the side panel by following the instructions in
“Replacing the side panel” on page 52
.
Replacing the memory card
reader
To replace the memory card reader:
1
Remove the side panel by following the instructions in
“Removing the side panel” on page 49
.
2
Remove the front bezel by following the instructions in
“Removing the front bezel” on page 51
.
3
Disconnect the memory card reader cables, noting their
locations and orientation. (You will reconnect the cables
after you install the new memory card reader.)