HP 300X HP Jetdirect Print Server Administrator's Guide (300x, 510x) - Page 69

Table 7.2, General HP Jetdirect Messages 1 of 10, HP Jetdirect Configuration Messages 69

Get HP 300X - JetDirect Print Server PDF manuals and user guides
UPC - 882780300842
View all HP 300X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Table 7.2 General HP Jetdirect Messages (1 of 10) Message Description ARP DUPLICATE IP ADDRESS The ARP layer has detected another node on the network using the same IP address as the HP Jetdirect print server. Extended error information below this message shows the hardware address of the other node. BABBLE ERROR Run the power-on self-test: turn the printer off, then on again. If the error persists, replace the HP Jetdirect print server. For information on replacing your HP Jetdirect print server, see the hardware installation guide for your print server. BAD BOOTP REPLY An error was detected in the BOOTP reply that the HP Jetdirect print server received. The BOOTP reply either had insufficient data in the UDP datagram to contain the minimum BOOTP header of 236 bytes, had an operation field that was not BOOTPREPLY(0X02), had a header field that did not match the print servers hardware address, or had a UDP source port that was not the BOOTP server port (67/udp). BAD BOOTP TAG SIZE The tagsize in a vendor specific field in the BOOTP reply is either 0, or greater than the remaining number of unprocessed bytes in the vendor specified area. BOOTP/DHCP IN PROGRESS The HP Jetdirect print server is currently in the process of obtaining its basic IP configuration information through BOOTP/DHCP, and has not detected any errors. CF ERR - ACCESS LIST The TFTP configuration file specified too many access list EXCEEDED entries using the "allow:" keyword. CF ERR - FILE INCOMPLETE The TFTP configuration file contained an incomplete last line that did not end in a newline character. CF ERR - INVALID PARAM A line in the TFTP configuration file contained an invalid value for one of the parameters on that line. CF ERR - LINE TOO LONG A line being processed in the TFTP configuration file was longer than the HP Jetdirect print server could accept. CF ERR - MISSING PARAM A line in the TFTP configuration file was missing a required parameter. CF ERR - TRAP LIST EXCEEDED The TFTP configuration file specified too many trap destination list entries using the "trap-destination:" keyword. CF ERR - UNKNOWN KEYWORD A TFTP configuration file line contained an unknown keyword. ENWW HP Jetdirect Configuration Page Messages 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
ENWW
HP Jetdirect Configuration Page Messages 69
Table 7.2
General HP Jetdirect Messages (1 of 10)
Message
Description
ARP DUPLICATE IP
ADDRESS
The ARP layer has detected another node on the network
using the same IP address as the HP Jetdirect print
server. Extended error information below this message
shows the hardware address of the other node.
BABBLE ERROR
Run the power-on self-test: turn the printer off, then on
again. If the error persists, replace the HP Jetdirect print
server. For information on replacing your HP Jetdirect
print server, see the hardware installation guide for your
print server.
BAD BOOTP REPLY
An error was detected in the BOOTP reply that the
HP Jetdirect print server received. The BOOTP reply
either had insufficient data in the UDP datagram to contain
the minimum BOOTP header of 236 bytes, had an
operation field that was not BOOTPREPLY(0X02), had a
header field that did not match the print servers hardware
address, or had a UDP source port that was not the
BOOTP server port (67/udp).
BAD BOOTP TAG SIZE
The tagsize in a vendor specific field in the BOOTP reply
is either 0, or greater than the remaining number of
unprocessed bytes in the vendor specified area.
BOOTP/DHCP IN
PROGRESS
The HP Jetdirect print server is currently in the process of
obtaining its basic IP configuration information through
BOOTP/DHCP, and has not detected any errors.
CF ERR - ACCESS LIST
EXCEEDED
The TFTP configuration file specified too many access list
entries using the “allow:” keyword.
CF ERR - FILE
INCOMPLETE
The TFTP configuration file contained an incomplete last
line that did not end in a newline character.
CF ERR - INVALID
PARAM
A line in the TFTP configuration file contained an invalid
value for one of the parameters on that line.
CF ERR - LINE TOO
LONG
A line being processed in the TFTP configuration file was
longer than the HP Jetdirect print server could accept.
CF ERR - MISSING
PARAM
A line in the TFTP configuration file was missing a required
parameter.
CF ERR - TRAP LIST
EXCEEDED
The TFTP configuration file specified too many trap
destination list entries using the “trap-destination:”
keyword.
CF ERR - UNKNOWN
KEYWORD
A TFTP configuration file line contained an unknown
keyword.