HP 300X HP Jetdirect Print Server Administrator's Guide (300x, 510x) - Page 71

Table 7.2, General HP Jetdirect Messages 3 of 10, HP Jetdirect Configuration Messages 71

Get HP 300X - JetDirect Print Server PDF manuals and user guides
UPC - 882780300842
View all HP 300X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Table 7.2 General HP Jetdirect Messages (3 of 10) Message Description INITIALIZING TRYING TO CONNECT TO SERVER The HP Jetdirect print server is trying to connect to the NetWare server(s). This is a normal message. Wait until the connection is established or another status message appears. INVALID GATEWAY ADDRESS The default gateway IP address specified for the HP Jetdirect print server (through BOOTP or NOVRAM) is an invalid IP address for specifying a single node. INVALID IP ADDRESS The IP address specified for the HP Jetdirect print server (through BOOTP or NOVRAM) is an invalid IP address for specifying a single node. INVALID SERVER ADDRESS The TFTP server IP address specified for the HP Jetdirect print server (through BOOTP) is an invalid IP address for specifying a single node. INVALID SUBNET MASK The IP subnet mask specified for the HP Jetdirect print server (through BOOTP or NOVRAM) is an invalid subnet mask. INVALID SYSLOG ADDRESS The syslog server IP address specified for the HP Jetdirect print server (through BOOTP) is an invalid IP address for specifying a single node. INVALID TRAP DEST ADDRESS One of the SNMP trap (Trap PDU) destination IP addresses specified for the HP Jetdirect print server (through TFTP) is an invalid IP address for specifying a single node. I/O CARD INITIALIZING (INIT) The HP Jetdirect print server is initializing the network protocols. For more information, see the network operating system status line on the configuration page. I/O CARD NOT READY There is a problem with the print server or its configuration. Following the I/O CARD NOT READY message is a status message. See this table for a detailed explanation of all status messages. I/O CARD READY The HP Jetdirect print server is connected and awaiting data. LAN ERROR-AUTO REMOVAL Run the power-on self-test: turn the printer off, then on again. If this message reappears on another configuration page, you may have a problem with one of the HP Jetdirect print servers on your network. Check all the print servers on the network for proper operation. LAN ERROR-BABBLE Check the network connections. If the connections are intact, run the power-on self-test: turn the printer off, then on again. If the error persists, replace the HP Jetdirect print server. For replacement instructions, see the hardware installation guide for your print server. ENWW HP Jetdirect Configuration Page Messages 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
ENWW
HP Jetdirect Configuration Page Messages 71
INITIALIZING TRYING
TO CONNECT TO
SERVER
The HP Jetdirect print server is trying to connect to the
NetWare server(s). This is a normal message. Wait until
the connection is established or another status message
appears.
INVALID GATEWAY
ADDRESS
The default gateway IP address specified for the
HP Jetdirect print server (through BOOTP or NOVRAM)
is an invalid IP address for specifying a single node.
INVALID IP ADDRESS
The IP address specified for the HP Jetdirect print server
(through BOOTP or NOVRAM) is an invalid IP address for
specifying a single node.
INVALID SERVER
ADDRESS
The TFTP server IP address specified for the HP Jetdirect
print server (through BOOTP) is an invalid IP address for
specifying a single node.
INVALID SUBNET MASK
The IP subnet mask specified for the HP Jetdirect print
server (through BOOTP or NOVRAM) is an invalid subnet
mask.
INVALID SYSLOG
ADDRESS
The syslog server IP address specified for the
HP Jetdirect print server (through BOOTP) is an invalid IP
address for specifying a single node.
INVALID TRAP DEST
ADDRESS
One of the SNMP trap (Trap PDU) destination IP
addresses specified for the HP Jetdirect print server
(through TFTP) is an invalid IP address for specifying a
single node.
I/O CARD INITIALIZING
(INIT)
The HP Jetdirect print server is initializing the network
protocols. For more information, see the network
operating system status line on the configuration page.
I/O CARD NOT READY
There is a problem with the print server or its configuration.
Following the I/O CARD NOT READY message is a status
message. See this table for a detailed explanation of all
status messages.
I/O CARD READY
The HP Jetdirect print server is connected and awaiting
data.
LAN ERROR-AUTO
REMOVAL
Run the power-on self-test: turn the printer off, then on
again. If this message reappears on another configuration
page, you may have a problem with one of the HP Jetdirect
print servers on your network. Check all the print servers
on the network for proper operation.
LAN ERROR-BABBLE
Check the network connections. If the connections are
intact, run the power-on self-test: turn the printer off, then
on again. If the error persists, replace the HP Jetdirect
print server. For replacement instructions, see the
hardware installation guide for your print server.
Table 7.2
General HP Jetdirect Messages (3 of 10)
Message
Description