HP 300X HP Jetdirect Print Server Administrator's Guide (300x, 510x) - Page 72

Table 7.2, General HP Jetdirect Messages 4 of 10

Get HP 300X - JetDirect Print Server PDF manuals and user guides
UPC - 882780300842
View all HP 300X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Table 7.2 General HP Jetdirect Messages (4 of 10) Message Description LAN ERROR-CONTROLLER CHIP Check the network connections. If the connections are intact, run the power-on self-test: turn the printer off, then on again. If the error persists, replace the HP Jetdirect print server. LAN ERROR-EXTERNAL LOOPBACK The HP Jetdirect print server is incorrectly connected to your network or is defective. Make sure your HP Jetdirect print server is correctly attached to your network. In addition, check the cabling and connectors. LAN ERROR-INFINITE DEFERRAL There is a network congestion problem. Check network cables. Note: If the print server is not connected to the network, this error cannot occur. LAN ERROR-INTERNAL Check all network connections. LOOPBACK LAN ERROR-LOSS OF CARRIER Check the network connections. If the connections are intact, run the power-on self-test: turn the print server off, then on again. If the error persists, replace the HP Jetdirect print server. LAN ERROR-NO LINKBEAT This message is displayed if Link Beat is not sensed. Check the network cable, and verify that the concentrator/hub is providing Link Beat. LAN ERROR-NO SQE Check the network connections. If the connections are intact, run the power-on self-test: turn the print server off, then on again. If the error persists, replace the HP Jetdirect print server. LAN ERROR-RECEIVER OFF There may be a problem with your network cabling or the HP Jetdirect print server. Check the cabling and connectors on your Ethernet network. If you cannot find a problem with your network cabling, run the power-on self-test: turn the print server off, then on again. If the error persists after the printer is turned on again, there is a problem with the HP Jetdirect print server. LAN ERROR-REMOVE RECEIVE Run the power-on self-test: turn the print server off, then on again. If this message reappears on the resulting configuration page, you may have a problem with one of the HP Jetdirect print servers on your network. Check all the HP Jetdirect print servers on the network for proper operation. LAN ERROR-RETRY FAULTS There is a problem with your network cabling or external network configuration. Check the network cables and connections. Verify operation of the hub or switch port. 72 HP Jetdirect Configuration Page Messages ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
72 HP Jetdirect Configuration Page Messages
ENWW
LAN
ERROR-CONTROLLER
CHIP
Check the network connections. If the connections are
intact, run the power-on self-test: turn the printer off, then
on again. If the error persists, replace the HP Jetdirect
print server.
LAN ERROR-EXTERNAL
LOOPBACK
The HP Jetdirect print server is incorrectly connected to
your network or is defective. Make sure your HP Jetdirect
print server is correctly attached to your network. In
addition, check the cabling and connectors.
LAN ERROR-INFINITE
DEFERRAL
There is a network congestion problem. Check network
cables.
Note:
If the print server is not connected to the network,
this error cannot occur.
LAN ERROR-INTERNAL
LOOPBACK
Check all network connections.
LAN ERROR-LOSS OF
CARRIER
Check the network connections. If the connections are
intact, run the power-on self-test: turn the print server off,
then on again. If the error persists, replace the
HP Jetdirect print server.
LAN ERROR-NO
LINKBEAT
This message is displayed if Link Beat is not sensed.
Check the network cable, and verify that the
concentrator/hub is providing Link Beat.
LAN ERROR-NO SQE
Check the network connections. If the connections are
intact, run the power-on self-test: turn the print server off,
then on again. If the error persists, replace the
HP Jetdirect print server.
LAN ERROR-RECEIVER
OFF
There may be a problem with your network cabling or the
HP Jetdirect print server. Check the cabling and
connectors on your Ethernet network. If you cannot find a
problem with your network cabling, run the power-on
self-test: turn the print server off, then on again. If the error
persists after the printer is turned on again, there is a
problem with the HP Jetdirect print server.
LAN ERROR-REMOVE
RECEIVE
Run the power-on self-test: turn the print server off, then
on again. If this message reappears on the resulting
configuration page, you may have a problem with one of
the HP Jetdirect print servers on your network. Check all
the HP Jetdirect print servers on the network for proper
operation.
LAN ERROR-RETRY
FAULTS
There is a problem with your network cabling or external
network configuration. Check the network cables and
connections. Verify operation of the hub or switch port.
Table 7.2
General HP Jetdirect Messages (4 of 10)
Message
Description