HP Integrity rx8620 Installation Guide, Sixth Edition - HP Integrity rx8620 Se - Page 28

HP Integrity rx8620 Server Description, Dimensions and Components,

Get HP Integrity rx8620 PDF manuals and user guides View all HP Integrity rx8620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Introduction Detailed HP Integrity rx8620 Server Description HP Integrity rx8620 Server Description Dimensions and Components Figure 1-13 HP Integrity rx8620 Server (Front View) Removable Media Drive PCI Power Supply Power Switch Hard Disk Drive Front OLR Fan Bulk Power Supply • Depth: Defined by cable management constraints to fit into a standard 36-inch deep rack: 25.5 inches from front rack column to PCI connector surface 26.7 inches from front rack column to core I/O card connector surface 30 inches overall package dimension, including 2.7 inches protruding in front of the front rack columns • Width: 17.5 inches, constrained by EIA standard 19 inch racks • Height: 17U (29.55 inches), constrained by package density The mass storage section located in the front allows access to removable media drives without removal of the bezel (bezel not shown in figure). The mass storage bay accommodates two 5.25-inch removable media drives and up to four 3.5-inch hard disk drives. The front panel display, containing LEDs and the system power switch, is located directly above the hard drive media bays. Below the mass storage section and behind a removable bezel are two PCI DC-to-DC power supplies. Each PCI power supply will power only one I/O partition. Enclosed with protective finger guards are nine front online replace (OLR) fan modules. The bulk power supply is partitioned through the use of a sealed metallic enclosure located in the bottom of the server. This enclosure houses the N+1 fully redundant bulk power supplies. These power supplies are installed from the front of the server after removing the front bezel. The power supply is 2.45 X 5.625 X 20.0 inches. 28 Chapter 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Chapter 1
Introduction
Detailed HP Integrity rx8620 Server Description
28
HP Integrity rx8620 Server Description
Dimensions and Components
Figure 1-13
HP Integrity rx8620 Server (Front View)
•
Depth: Defined by cable management constraints to fit into a standard 36-inch deep rack:
25.5 inches from front rack column to PCI connector surface
26.7 inches from front rack column to core I/O card connector surface
30 inches overall package dimension, including 2.7 inches protruding in front of the front rack columns
•
Width
: 17.5 inches, constrained by EIA standard 19 inch racks
•
Height
: 17U (29.55 inches), constrained by package density
The mass storage section located in the front allows access to removable media drives without removal of the
bezel (bezel not shown in figure). The mass storage bay accommodates two 5.25-inch removable media drives
and up to four 3.5-inch hard disk drives. The front panel display, containing LEDs and the system power
switch, is located directly above the hard drive media bays.
Below the mass storage section and behind a removable bezel are two PCI DC-to-DC power supplies. Each
PCI power supply will power only one I/O partition.
Enclosed with protective finger guards are nine front online replace (OLR) fan modules.
The bulk power supply is partitioned through the use of a sealed metallic enclosure located in the bottom of
the server. This enclosure houses the N+1 fully redundant bulk power supplies. These power supplies are
installed from the front of the server after removing the front bezel. The power supply is
2.45 X 5.625 X 20.0 inches.
Bulk Power Supply
Removable Media Drive
PCI Power Supply
Hard Disk Drive
Power Switch
Front OLR Fan