HP Integrity rx8620 Installation Guide, Sixth Edition - HP Integrity rx8620 Se - Page 63

DVD+RW Installation Instructions, Step 1.

Get HP Integrity rx8620 PDF manuals and user guides View all HP Integrity rx8620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Installation Installing Accessories DVD+RW Installation Instructions The CD/DVD/DAT is located in the front of the chassis. The system power to this component must be removed before attempting to remove or replace it. Follow the procedures below to install the DVD+RW drive. Figure 2-19 Removable Media Bay Location Step 1. Remove the front bezel and top cover. See "Removing the Front Bezel" and "Removing the Top Cover" in the Remove and Replace Procedures of the HP Service Guide. Step 2. Remove the drive bay blank or removable media drive. NOTE In the HP Integrity rx8620 Server, the upper removable media drive must be removed to access the lower removable media drive. Step 3. Remove the DVD+RW drive from package. Step 4. Install the side rails onto the drive. Step 5. Connect the removable media bay power cable to the loose end of the Y power cable on the DVD+RW assembly. Ensure that the mating connector pair passes through the ruggedizer. Step 6. Route the removable media bay power cable into the ruggedizer cable clip. Step 7. Connect the SCSI cable to the DVD+RW dive. Ensure that the power cable passes over the top of the SCSI cable. Chapter 2 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Chapter 2
Installation
Installing Accessories
63
DVD+RW Installation Instructions
The CD/DVD/DAT is located in the front of the chassis. The system power to this component must be removed
before attempting to remove or replace it. Follow the procedures below to install the DVD+RW drive.
Figure 2-19
Removable Media Bay Location
Step 1.
Remove the front bezel and top cover. See “Removing the Front Bezel” and “Removing the Top
Cover” in the Remove and Replace Procedures of the HP Service Guide.
Step 2.
Remove the drive bay blank or removable media drive.
NOTE
In the HP Integrity rx8620 Server, the upper removable media drive must be
removed to access the lower removable media drive.
Step 3.
Remove the DVD+RW drive from package.
Step 4.
Install the side rails onto the drive.
Step 5.
Connect the removable media bay power cable to the loose end of the Y power cable on the
DVD+RW assembly. Ensure that the mating connector pair passes through the ruggedizer.
Step 6.
Route the removable media bay power cable into the ruggedizer cable clip.
Step 7.
Connect the SCSI cable to the DVD+RW dive. Ensure that the power cable passes over the top of
the SCSI cable.